makka
Member

220 Likes

Page 3 of 15 First 123456789101112131415 Last

• Jump to page:

1. 
   rupert liked post by makka On thread : 5.6x57 single shot project

   Once I got my hands on a .224 barrel(unfired CZ barrel, 24" 1:9 twist) it was time to stub the shotgun barrel and bore the first 110mm to 21mm so the forcing cone was gone and there was a step to...

   Liked On: 28-05-2024, 11:38 AM

2. 
   rupert liked post by makka On thread : 5.6x57 single shot project

   I have been tinkering around with this one for a while so thought I had better do a build thread on it. I picked up a cheap 12ga Baikal after seeing the 30-30 that akaroa1 had built. 251143 ...

   Liked On: 28-05-2024, 11:36 AM

3. 
   Micky Duck liked post by makka On thread : 5.6x57 single shot project

   Here is a close up of the extractor, showing the spring loaded detent that extracts the case. It is held in place against the spring by a roll pin. 251233 Once this was all sorted the barrel...

   Liked On: 28-05-2024, 09:59 AM

4. 
   schwen liked post by makka On thread : 5.6x57 single shot project

   Here is a close up of the extractor, showing the spring loaded detent that extracts the case. It is held in place against the spring by a roll pin. 251233 Once this was all sorted the barrel...

   Liked On: 28-05-2024, 08:50 AM

5. 
   tetawa liked post by makka On thread : 5.6x57 single shot project

   Here is a close up of the extractor, showing the spring loaded detent that extracts the case. It is held in place against the spring by a roll pin. 251233 Once this was all sorted the barrel...

   Liked On: 28-05-2024, 08:17 AM

6. 
   tetawa liked post by makka On thread : 5.6x57 single shot project

   Once I got my hands on a .224 barrel(unfired CZ barrel, 24" 1:9 twist) it was time to stub the shotgun barrel and bore the first 110mm to 21mm so the forcing cone was gone and there was a step to...

   Liked On: 28-05-2024, 08:16 AM

7. 
   stug liked post by makka On thread : 5.6x57 single shot project

   Here is a close up of the extractor, showing the spring loaded detent that extracts the case. It is held in place against the spring by a roll pin. 251233 Once this was all sorted the barrel...

   Liked On: 28-05-2024, 12:23 AM

8. 
   7mm tragic liked post by makka On thread : 5.6x57 single shot project

   Next step was to mill a slot for the extractor and test fit it. 251216 That was all good so milled the old extractor off and tig'd this one in place. Also drilled and tapped the shotgun barrel...

   Liked On: 27-05-2024, 10:28 PM

9. 
   csmiffy liked post by makka On thread : 5.6x57 single shot project

   Next step was to mill a slot for the extractor and test fit it. 251216 That was all good so milled the old extractor off and tig'd this one in place. Also drilled and tapped the shotgun barrel...

   Liked On: 27-05-2024, 10:05 PM

10. 
    Micky Duck liked post by makka On thread : 5.6x57 single shot project

    Next step was to mill a slot for the extractor and test fit it. 251216 That was all good so milled the old extractor off and tig'd this one in place. Also drilled and tapped the shotgun barrel...

    Liked On: 27-05-2024, 09:53 PM

11. 
    Steelisreal liked post by makka On thread : 5.6x57 single shot project

    Once I got my hands on a .224 barrel(unfired CZ barrel, 24" 1:9 twist) it was time to stub the shotgun barrel and bore the first 110mm to 21mm so the forcing cone was gone and there was a step to...

    Liked On: 27-05-2024, 07:33 PM

12. 
    Steelisreal liked post by makka On thread : 5.6x57 single shot project

    Whilst I was waiting for a .224 barrel to appear I started work on the extractor as I knew it would be a bit of work to make an extractor for a rimless cartridge. I began by drilling a 12mm hole in...

    Liked On: 27-05-2024, 07:33 PM

13. 
    Steelisreal liked post by makka On thread : 5.6x57 single shot project

    I have been tinkering around with this one for a while so thought I had better do a build thread on it. I picked up a cheap 12ga Baikal after seeing the 30-30 that akaroa1 had built. 251143 ...

    Liked On: 27-05-2024, 07:33 PM

14. 
    SixtyTen liked post by makka On thread : 5.6x57 single shot project

    Once I got my hands on a .224 barrel(unfired CZ barrel, 24" 1:9 twist) it was time to stub the shotgun barrel and bore the first 110mm to 21mm so the forcing cone was gone and there was a step to...

    Liked On: 27-05-2024, 06:18 PM

15. 
    nickbop liked post by makka On thread : 5.6x57 single shot project

    Once I got my hands on a .224 barrel(unfired CZ barrel, 24" 1:9 twist) it was time to stub the shotgun barrel and bore the first 110mm to 21mm so the forcing cone was gone and there was a step to...

    Liked On: 27-05-2024, 05:23 PM

Page 3 of 15 First 123456789101112131415 Last

• Jump to page: