Marty Henry
Member

2876 Likes

Page 104 of 192 First ... 45490919293949596979899100101102103104105106107108109110111112113114115116117118154 ... Last

• Jump to page:

1. 
   Marty Henry liked post by Lucky On thread : Oberndorf Mauser

   Ok fellas here’s another one , 1931 Kurz , these are short actions and were made on lots of configurations , eg , Type A with Kurz action , Type M with Kurz action etc , this one is a Type B Kurz in...

   Liked On: 21-08-2021, 05:12 PM

2. 
   Marty Henry liked post by MSL On thread : show us your chainsaws

   60”, have 72” also Sent from my iPhone using Tapatalk

   Liked On: 21-08-2021, 01:54 PM

3. 
   Marty Henry liked post by veitnamcam On thread : Breakfast thread

   Fresh Fallow liver with bacon, mushrooms, onions all fried in butter on some toast.142502

   Liked On: 21-08-2021, 11:18 AM

4. 
   Marty Henry liked post by XR500 On thread : show us your chainsaws

   No, not porn. Here's a double ender in action;) 175628

   Liked On: 21-08-2021, 08:45 AM

5. 
   Marty Henry liked post by Friwi On thread : threading odd muzzle

   @ 303, when we re open after the lockdown, bring your rifle along at our workshop at dpt and I can take measurements and see what we can do for you.

   Liked On: 20-08-2021, 10:12 PM

6. 
   Marty Henry liked post by Micky Duck On thread : threading odd muzzle

   well it appears Friwi is willing to have a look......job done one would say.

   Liked On: 20-08-2021, 10:12 PM

7. 
   Marty Henry liked post by gundoc On thread : threading odd muzzle

   It can be internally threaded and an adapter made but it must be done on a lathe with a 4-jaw chuck and clocked true with the bore using a neat fitting spud. Any proper gunsmith should whack it out...

   Liked On: 20-08-2021, 10:11 PM

8. 
   Marty Henry liked post by XR500 On thread : show us your chainsaws

   Flapper disc on an angle grinder has those whisker sharp in a giffy!

   Liked On: 20-08-2021, 03:27 PM

9. 
   Marty Henry liked post by shooternz On thread : Subsonic 7mm loads

   The problem with the 7mm as a subsonic calibre is the twist rate it won't stabilise bullets longer than my 133 HP and the higher velocity is limited by the twist rate to 1700fps it really is too...

   Liked On: 20-08-2021, 11:33 AM

10. 
    Marty Henry liked post by The bomb On thread : 40 meter patterns-advice please

    Kill geese with 1oz #4 in 20g with a full choke,lead the white cheek patch as your target like shooting a quail.get the pellets on head and neck the smaller pellets and denser pattern kill well.

    Liked On: 20-08-2021, 11:30 AM

11. 
    Marty Henry liked post by rewa On thread : Thoughts on BSA CF2 270?

    I've got one in .270, I think its a CF2, but might be a Monarch. Nice rifle, shoots fine and way (way) lighter than my Sako AV 6.5x55. I think its a transition model..maybe. 1970-ish. Twin...

    Liked On: 20-08-2021, 09:33 AM

12. 
    Marty Henry liked post by Seventenths On thread : show us your chainsaws

    Here's my two saws I currently own one being a Husky 288 and a 495 and both are awesome saws but at the moment I'm looking at upgrading to either a 572XP or 395 so in a month I'll see what I get. ...

    Liked On: 20-08-2021, 08:26 AM

13. 
    Marty Henry liked post by Allgood On thread : Oberndorf Mauser

    1908 Oberndorf Mauser Model B Sporter in 10.75X68............... 175368 175369 175371 175372

    Liked On: 19-08-2021, 08:07 AM

14. 
    Marty Henry liked post by Lucky On thread : Oberndorf Mauser

    Thought some good rifle porn was required while in lockdown , so let’s start a thread on Pre-war Oberndorf sporting rifles , I’m sure a few of you will have 1 or 2 lurking in the gun cabinet , this...

    Liked On: 19-08-2021, 08:03 AM

15. 
    Marty Henry liked post by Rich007 On thread : 40 meter patterns-advice please

    Try a few different types of ammo, when I did this a few years back I was amazed by the difference in pattern consistency and density between ammo types

    Liked On: 19-08-2021, 08:02 AM

Page 104 of 192 First ... 45490919293949596979899100101102103104105106107108109110111112113114115116117118154 ... Last

• Jump to page: