McNotty
Member

1095 Likes

Page 68 of 73 First ... 185455565758596061626364656667686970717273 Last

• Jump to page:

1. 
   Hunter_killer liked post by McNotty On thread : 7mmRM project

   Unless you’re experienced and can take pretty fine measurements, most people back off from lands 20 thou (0.5mm) and start playing with seating depth from there.

   Liked On: 28-02-2019, 06:10 AM

2. 
   Hunter_killer liked post by McNotty On thread : 7mmRM project

   stagstalker have you got any 2217 spare? Yea, red is max. But you could find your rifle doesn't mind over max. Seating depth in relation to lands will also affect pressure. Sorry for the shit image,...

   Liked On: 27-02-2019, 09:37 AM

3. 
   Hunter_killer liked post by McNotty On thread : 7mmRM project

   Nothing wrong with a 22 inch barrel in 7mmRM. Pretty sure Duleys get decent results with 20" version so I wouldn't worry too much. Mate owns a 22" and regularly shoots 5-600m with no issues at...

   Liked On: 27-02-2019, 08:36 AM

4. 
   Micky Duck liked post by McNotty On thread : Tikka 223 not grouping after shortening

   105077 So....turns out someone (this dick) hadn’t tightened the locking ring on the front of the scope and it had a little bit of play. Had all but given up hope till I found the same issue when...

   Liked On: 17-02-2019, 05:59 PM

5. 
   Flyblown liked post by McNotty On thread : Tikka 223 not grouping after shortening

   105077 So....turns out someone (this dick) hadn’t tightened the locking ring on the front of the scope and it had a little bit of play. Had all but given up hope till I found the same issue when...

   Liked On: 15-02-2019, 09:21 PM

6. 
   canross liked post by McNotty On thread : How to Hang a Gong

   WillB I’m in Welly mate, can come grab some conveyor rubber straps off me if you’d like. I put a pipe spacer in at the back to create a downward angle for splash down and takes a bit of sting out as...

   Liked On: 12-02-2019, 10:15 AM

7. 
   Monk liked post by McNotty On thread : 300WSM 165g Scirocco

   Monk is that mag length and Tikka? Are you far from max? I've got hornady manual so can look up, pretty sure is lists Reloader17 in 178gr data.

   Liked On: 12-02-2019, 09:04 AM

8. 
   Ingrid 51 liked post by McNotty On thread : WTB: 6.5x55 Hornady Lock ‘n Load gauge, comparator etc

   Chuck this in buy,sell section, there’s a lot more eyes there :thumbsup:

   Liked On: 11-02-2019, 11:34 PM

9. 
   Moa Hunter liked post by McNotty On thread : Wind indictor

   104858 Not the most portable but shit she's accurate :pacman:

   Liked On: 11-02-2019, 03:38 PM

10. 
    ChrisW liked post by McNotty On thread : What’s your rig?

    Soon to be picked up and into load development. 20 inch Tikka wsm with new dpt mk2 and vx5. Try out some Reloader 17 behind the 178 ELDX. Few things to add on, cheek riser, limbsaver and ballistic...

    Liked On: 07-02-2019, 09:26 AM

11. 
    JoshC liked post by McNotty On thread : What’s your rig?

    Soon to be picked up and into load development. 20 inch Tikka wsm with new dpt mk2 and vx5. Try out some Reloader 17 behind the 178 ELDX. Few things to add on, cheek riser, limbsaver and ballistic...

    Liked On: 07-02-2019, 08:25 AM

12. 
    stagstalker liked post by McNotty On thread : What’s your rig?

    Soon to be picked up and into load development. 20 inch Tikka wsm with new dpt mk2 and vx5. Try out some Reloader 17 behind the 178 ELDX. Few things to add on, cheek riser, limbsaver and ballistic...

    Liked On: 06-02-2019, 03:54 PM

13. 
    rewa liked post by McNotty On thread : Advice from welders please

    Go manual mate, you'll get used to nodding the hood down and plus you don't have lift helmet to do any grinding. Just lift flap and grind. I know the autos can have a grind setting, but it's never...

    Liked On: 03-02-2019, 09:46 PM

14. 
    oraki liked post by McNotty On thread : Advice from welders please

    Go manual mate, you'll get used to nodding the hood down and plus you don't have lift helmet to do any grinding. Just lift flap and grind. I know the autos can have a grind setting, but it's never...

    Liked On: 31-01-2019, 12:54 PM

15. 
    veitnamcam liked post by McNotty On thread : How to Hang a Gong

    WillB I’m in Welly mate, can come grab some conveyor rubber straps off me if you’d like. I put a pipe spacer in at the back to create a downward angle for splash down and takes a bit of sting out as...

    Liked On: 31-01-2019, 06:17 AM

Page 68 of 73 First ... 185455565758596061626364656667686970717273 Last

• Jump to page: