McNotty
Member

264 Likes

Page 5 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   McNotty liked post by Chur Bay On thread : Dry Aging Fish

   Awesome :cool:

   Liked On: 24-03-2022, 06:50 PM

2. 
   McNotty liked post by LHF On thread : Twin Loads - Bush and LR

   If you already have a load for the 178 then I'd use that. I'm running an 18" WSM with 178s, they work fine from 8yds to 550+.

   Liked On: 09-03-2022, 10:10 PM

3. 
   McNotty liked post by Beetroot On thread : Twin Loads - Bush and LR

   If you enjoy reloading and have the components I see no problems with 2 different loads. If the bush load shoots close enough POI and a you are shooting within 200m then it'd be easy as. As...

   Liked On: 09-03-2022, 10:10 PM

4. 
   McNotty liked post by wsm junkie On thread : Twin Loads - Bush and LR

   I run 208's @2820 from 22" barrel for everything near or far. It's a pretty mild load and could get 100fps on that if i stoked it up a bit so would guess you could get 2650-2700 with the 18" barrel....

   Liked On: 09-03-2022, 10:10 PM

5. 
   McNotty liked post by Micky Duck On thread : Twin Loads - Bush and LR

   sounds like a plan Stan.......I used the hornadies as were closest thing I could find terminal wise to winchester 180grn factory loadings. sure couldnt complain about how they worked.have heard good...

   Liked On: 08-03-2022, 09:00 PM

6. 
   McNotty liked post by mikee On thread : Twin Loads - Bush and LR

   One load for everything means less chance of MrMurphy popping his head up!!

   Liked On: 08-03-2022, 09:35 AM

7. 
   McNotty liked post by stug On thread : Twin Loads - Bush and LR

   Use a different projectile, that way you won’t get them confused. I’ve done this with a couple of rifles. Zero for the long range load then see where the bush load hits. So long as it is within an...

   Liked On: 08-03-2022, 08:59 AM

8. 
   McNotty liked post by rugerman On thread : Trailer recommendations

   Good to know. I planning on having a custom digger trailer made which will take my auger bits and drive unit as well, and have been hunting around a bit to see who to get to make it. maybe...

   Liked On: 01-03-2022, 08:34 PM

9. 
   McNotty liked post by Mr300WSM On thread : Gong Recommendations?

   I’ve got some here you can borrow if you want to try them out 30cm x 30cm 191084

   Liked On: 24-02-2022, 10:46 PM

10. 
    McNotty liked post by Ginga On thread : Thanks Leupold!

    Put in a padded box and send to - Leupold and Stevens PO Box 4985 Beaverton Oregon 97076-4985 USA Put a note in with it with problems and return address. Wait!

    Liked On: 19-09-2021, 07:05 PM

11. 
    McNotty liked post by Rushy On thread : Dinner thread?

    Shucks that sounds good VC. Little play on words there for those in the know. Ha ha ha ha

    Liked On: 19-09-2021, 06:21 PM

12. 
    McNotty liked post by Trout On thread : Dinner thread?

    All you need now is a beer with your nice pizza.178907

    Liked On: 19-09-2021, 12:27 PM

13. 
    McNotty liked post by bunji On thread : Dinner thread?

    The ground finally dried out enough to get the tractor up into the back block of the farm ,so spent the last couple of days clearing the wind fall off the fence lines. Pushed what was not wanted for...

    Liked On: 18-09-2021, 10:22 PM

14. 
    McNotty liked post by Seventenths On thread : show us your chainsaws

    Finally did it… just added a Husqvarna 572 XP to the stable. It’ll be a week or two before I get to use it properly but first impressions are good

    Liked On: 17-09-2021, 03:49 PM

15. 
    McNotty liked post by mace08 On thread : show us your chainsaws

    177961

    Liked On: 07-09-2021, 10:49 PM

Page 5 of 18 First 123456789101112131415161718 Last

• Jump to page: