mimms
Large Member

107 Likes

Page 3 of 8 First 12345678 Last

• Jump to page:

1. 
   Moa Hunter liked post by mimms On thread : Going from a super swede to a 45-70gov

   What is 300gn "underpowered" for??

   Liked On: 04-09-2019, 09:03 AM

2. 
   Cordite liked post by mimms On thread : Using iron sights

   I see what you did there :)

   Liked On: 04-09-2019, 12:02 AM

3. 
   Moa Hunter liked post by mimms On thread : Using iron sights

   I see what you did there :)

   Liked On: 02-09-2019, 06:58 PM

4. 
   outlander liked post by mimms On thread : Hi

   Hi I'm mimms and I'm an alcoholi/// shit sorry wrong website.

   Liked On: 02-09-2019, 10:36 AM

5. 
   GSP HUNTER liked post by mimms On thread : DIY Tactical Paint Job for Marlin

   Yeah... Mask off lenses. Everything else gets paint. (I see they even painted the bolt in that pic - you'd do that separately.) Super etch primer. Flat or ultra-flat paint colours. "krylon" brand is...

   Liked On: 29-08-2019, 10:47 AM

6. 
   madmaori liked post by mimms On thread : Sleeping bag advice

   Or support the NZ economy with domex, but whatever.

   Liked On: 28-08-2019, 05:05 PM

7. 
   Russian 22. liked post by mimms On thread : Sleeping bag advice

   Or support the NZ economy with domex, but whatever.

   Liked On: 28-08-2019, 01:13 PM

8. 
   diana2 liked post by mimms On thread : Kiln/Furnace for knife making heat treatment, who built one?

   As a matter of fact, I do. These are all old pics, it's slightly more refined now, with less to trip over. Pic 1 Is the shell, an old oil drum, top cut off, tuyere cut into the side down low and a...

   Liked On: 28-08-2019, 09:39 AM

9. 
   Moa Hunter liked post by mimms On thread : Sleeping bag advice

   Or support the NZ economy with domex, but whatever.

   Liked On: 28-08-2019, 09:33 AM

10. 
    sometimes1 liked post by mimms On thread : Hi

    Hi I'm mimms and I'm an alcoholi/// shit sorry wrong website.

    Liked On: 27-08-2019, 09:08 PM

11. 
    diana2 liked post by mimms On thread : Kiln/Furnace for knife making heat treatment, who built one?

    Not so much for knife making but I have a DIY furnace for melting/casting. Rammed DIY castable refractory and a waste-motor-oil burner. Cheap to build and to burn. Not too particular on temp...

    Liked On: 27-08-2019, 05:59 PM

12. 
    Moa Hunter liked post by mimms On thread : Using iron sights

    I'm one of those, too. Twink probably gives dolphins cancer or something, but CRC do paint marking pens, avail at your friendly local engineering shop.

    Liked On: 26-08-2019, 12:38 AM

13. 
    Moa Hunter liked post by mimms On thread : Leaving your Suppressor on.....what happens.

    Crown looks fine and threads would clean up with a wire brush... Being dissimilar metals, galling shouldn't even be an issue.

    Liked On: 25-08-2019, 10:31 PM

14. 
    Jit liked post by mimms On thread : Leaving your Suppressor on.....what happens.

    Crown looks fine and threads would clean up with a wire brush... Being dissimilar metals, galling shouldn't even be an issue.

    Liked On: 25-08-2019, 05:25 PM

15. 
    Rated M for Magnum liked post by mimms On thread : Factory .308 ammo for 16" Tikka to 300m+?

    I had a couple of boxes hornady, fricken expensive alright. Wouldn't group for shit till I pulled the bullets and re-seated them just off the lands, then sub-moa.

    Liked On: 24-08-2019, 03:17 PM

Page 3 of 8 First 12345678 Last

• Jump to page: