No.3
Member

1650 Likes

Page 34 of 110 First ... 202122232425262728293031323334353637383940414243444546474884 ... Last

• Jump to page:

1. 
   rupert liked post by No.3 On thread : Boat Trailer Maintenance Time

   Well, if you do the maintenance... If I'm using a trailer heavily repack the hub bearings with fresh grease every couple of months or so? The other one is bearing buddies - they can be a problem if...

   Liked On: 21-11-2023, 10:15 PM

2. 
   Micky Duck liked post by No.3 On thread : 22 cal smoothbore vs rifled 22lr bore RE SHOT SHELLS

   Yeah, apparently there was testing done on this with shot in rifled barrels and the only way they got anything like acceptable patterning out of the shot column was for want of a better description a...

   Liked On: 21-11-2023, 07:46 PM

3. 
   Noswal liked post by No.3 On thread : 4x4 accessories

   Low as possible, below the bumper. It causes a slight lifting effect which helps the front end ride up and over/out from whatever you parked in - the opposite of what the high mounted recovery point...

   Liked On: 20-11-2023, 09:52 PM

4. 
   paremata liked post by No.3 On thread : 4x4 accessories

   Low as possible, below the bumper. It causes a slight lifting effect which helps the front end ride up and over/out from whatever you parked in - the opposite of what the high mounted recovery point...

   Liked On: 20-11-2023, 09:02 AM

5. 
   Noswal liked post by No.3 On thread : 4x4 accessories

   The front one is likely strong enough, but there are considerations with using a hook in that location. It's about 3-400mm higher than the equivalent chassis point, which doesn't seem like much but...

   Liked On: 19-11-2023, 10:22 PM

6. 
   BRADS liked post by No.3 On thread : 4x4 accessories

   The front one is likely strong enough, but there are considerations with using a hook in that location. It's about 3-400mm higher than the equivalent chassis point, which doesn't seem like much but...

   Liked On: 19-11-2023, 09:06 PM

7. 
   Marty Henry liked post by No.3 On thread : Return to zero QD mounts

   Try a small amount of silver nickel antiseize on the threads - this product 'dries' so doesn't seem to have the issue with coming loose like some thread lube products can and will help to protect...

   Liked On: 19-11-2023, 09:06 PM

8. 
   Eat Meater liked post by No.3 On thread : I need help! 270 barrel chop, cant make a decision

   My vote is 22" minimum for an -06 based cartridge. If you notice the difference between a 20 and a 22" barrel in the carry, you're either a bit like the princess in the "princess and the pea"...

   Liked On: 19-11-2023, 08:14 PM

9. 
   BSA270 liked post by No.3 On thread : Return to zero QD mounts

   The ones I have direct experience of are the Warne QD 'Maxima' series rings, these are a sintered product so you can't lap them like a machined ring. No issues in use between the QD and non-QD...

   Liked On: 18-11-2023, 10:06 PM

10. 
    Marty Henry liked post by No.3 On thread : Return to zero QD mounts

    The ones I have direct experience of are the Warne QD 'Maxima' series rings, these are a sintered product so you can't lap them like a machined ring. No issues in use between the QD and non-QD...

    Liked On: 18-11-2023, 04:07 PM

11. 
    Fssprecision liked post by No.3 On thread : Suppressed Lever Action

    I can see that being handy over dogs, also have a use as a close range homekill-type device for sorting animals in the yard.

    Liked On: 18-11-2023, 03:56 PM

12. 
    Micky Duck liked post by No.3 On thread : I need help! 270 barrel chop, cant make a decision

    Semantics. Should have added the disclaimer that my comments were for available factory loads, correct you can adjust things with reloading to offset some loss of barrel length. As far as the...

    Liked On: 17-11-2023, 06:34 PM

13. 
    Marty Henry liked post by No.3 On thread : I need help! 270 barrel chop, cant make a decision

    My vote is 22" minimum for an -06 based cartridge. If you notice the difference between a 20 and a 22" barrel in the carry, you're either a bit like the princess in the "princess and the pea"...

    Liked On: 17-11-2023, 02:57 PM

14. 
    buell984 liked post by No.3 On thread : Leupold Vx5 Leaked in the rain - 1 year old

    Seems Leupold and canted reticles from new is a thing then... It would also seem that there is quite a few Leupold scopes having issues with seals at the moment, and needing to be sent back - not...

    Liked On: 17-11-2023, 11:33 AM

15. 
    Rated M for Magnum liked post by No.3 On thread : Norinco JW15A 22 LR

    If it doesn't settle, and the stock tension adjustment doesn't change things look at the barrel and crown. If it's dirty give it a good clean, sometimes .22's (and I know most people think don't...

    Liked On: 17-11-2023, 10:05 AM

Page 34 of 110 First ... 202122232425262728293031323334353637383940414243444546474884 ... Last

• Jump to page: