No.3
Member

2665 Likes

Page 52 of 178 First ... 23839404142434445464748495051525354555657585960616263646566102152 ... Last

• Jump to page:

1. 
   Micky Duck liked post by No.3 On thread : Is this a Kelly axe

   Wa wa wa haha...

   Liked On: 19-08-2024, 01:27 PM

2. 
   hunter Al.7mm08 liked post by No.3 On thread : Is this a Kelly axe

   Apparently these were the ones exported to Aussie before Kelly entered the agreement to have them locally produced in Aussie. Hence the "Made in Canada" on one side, and the World's Finest Kelly...

   Liked On: 19-08-2024, 11:11 AM

3. 
   Micky Duck liked post by No.3 On thread : Is this a Kelly axe

   Apparently these were the ones exported to Aussie before Kelly entered the agreement to have them locally produced in Aussie. Hence the "Made in Canada" on one side, and the World's Finest Kelly...

   Liked On: 19-08-2024, 12:14 AM

4. 
   Micky Duck liked post by No.3 On thread : Suspect Wof

   Or like my old safari, put it into 4wd while in the que as i was bored - but forgot to unlock the auto hubs! Most even brake test the wof man had ever seen. Noted the new steering damper was loose,...

   Liked On: 19-08-2024, 12:04 AM

5. 
   gassedupbeans liked post by No.3 On thread : 7.62x39 or 357mag/38special for goats and similar sized animals

   ^^This... I've been using x39 on goats for a while, nice, light, well mannered and no performance issues at all with average cheap expanding hunting bullets. The FMJ is OK for plinking but not...

   Liked On: 18-08-2024, 06:21 PM

6. 
   Micky Duck liked post by No.3 On thread : Is this a Kelly axe

   Haha, good for cracked heels you reckon?

   Liked On: 18-08-2024, 04:29 PM

7. 
   sharps no 1 liked post by No.3 On thread : Is this a Kelly axe

   I would be comfortable with a cup brush with straight wires in an angle grinder to knock any really bad corrosion off, note this isn't a coated wire or twisted bristle wire buffing wheel just a bog...

   Liked On: 18-08-2024, 03:41 PM

8. 
   GR Journey's NZ liked post by No.3 On thread : New Hilux Auto Transmission Shudder?

   Against that, as a new vehicle the standard procedure for rectifying contamination at the dealer/maintainer appears to not been have followed which looks to have possibly created more issues. ...

   Liked On: 18-08-2024, 11:44 AM

9. 
   shananah liked post by No.3 On thread : White River Primers - Any misfire issues?

   Those ones that didn't go off look almost cupped from the firing pin strike to me - I would suggest that the issue may be related to what is for some reason known as primer sensitising during the...

   Liked On: 17-08-2024, 11:11 PM

10. 
    Micky Duck liked post by No.3 On thread : Is this a Kelly axe

    I looked at those Bahco poles when I was looking for a handle for my Hytest head - none in stock or available as the boat was delayed! There's another couple of brands available like Freund, Truper,...

    Liked On: 16-08-2024, 06:11 PM

11. 
    NZHunter2301 liked post by No.3 On thread : BT50 Freestyle cab rifle stowage

    Mate did something similar out of alloy, fold up doors on either end and some factory-ish seat pads on top with some grey carpet. Casually looking in you couldn't tell, the thing had a triangular...

    Liked On: 16-08-2024, 11:50 AM

12. 
    Micky Duck liked post by No.3 On thread : Is this a Kelly axe

    Nice. I got my last one from Leech wood products in CHCH, expensive but what isn't nowadays. What you will find is the average run of the mill axe handle from the hardware places now usually aren't...

    Liked On: 16-08-2024, 09:44 AM

13. 
    308 liked post by No.3 On thread : Is this a Kelly axe

    Yep, the chips on the edge look to be the worst of it. File flat with an engineers file, then reprofile the edge with the same tool and then sharpen. If you search for the us forestry manual or axe...

    Liked On: 16-08-2024, 08:41 AM

14. 
    XR500 liked post by No.3 On thread : Toasti - The Crispy Cruiser

    Probably the whole lot, every computer module, every interface, the entire loom, the entire safety fitting pack as well as the interior components and things like the glass parts. And that's if as...

    Liked On: 15-08-2024, 10:20 PM

15. 
    Micky Duck liked post by No.3 On thread : Toasti - The Crispy Cruiser

    Probably the whole lot, every computer module, every interface, the entire loom, the entire safety fitting pack as well as the interior components and things like the glass parts. And that's if as...

    Liked On: 15-08-2024, 08:42 PM

Page 52 of 178 First ... 23839404142434445464748495051525354555657585960616263646566102152 ... Last

• Jump to page: