No.3
Member

1604 Likes

Page 101 of 107 First ... 5187888990919293949596979899100101102103104105106107 Last

• Jump to page:

1. 
   Micky Duck liked post by No.3 On thread : New Hilux Fuel Consumption

   Yep to that, kinda sums it up. Most vehicles achieve best fuel economy in the region of 65-80km/h - going over that increases the drag effect exponentially and hits you in the arse pocket.

   Liked On: 15-07-2022, 02:36 PM

2. 
   Kopua Cowboy liked post by No.3 On thread : Hilux D4d injector knowledge

   Have you checked the on board computer readings against your actual real life using pump receipts for litres and a gps for mileage? If you fill to visible in the neck from say the 1/4 fill line on...

   Liked On: 12-07-2022, 07:46 PM

3. 
   T.FOYE liked post by No.3 On thread : Improving 45-70 ammo with a mandrel

   Looks like Revlon just branched out into multi-purpose lipstick ammo... On the subject of .45-70, this is definitly overthinking it in my book. .45-70 isn't a target round, so the need for 1/4"...

   Liked On: 12-07-2022, 12:45 AM

4. 
   flock liked post by No.3 On thread : STRAIGHTENING A CROOKED BULLET

   When seating, seat it half way then retract the case, turn it 180deg and run it to full depth. Seems to fix most of this issue. Another cause is a mismatch between the tip of the bullet and the...

   Liked On: 11-07-2022, 09:35 PM

5. 
   Jukes liked post by No.3 On thread : Rubber mats for ute tray & alternatives

   Whatever you get make sure it doesn't dissolve when you spill petrol onto it. That's a bugger as you invariably lose something out of a chainsaw, or tip a fuel can over and a lot of the cheaper...

   Liked On: 11-07-2022, 09:58 AM

6. 
   viper liked post by No.3 On thread : Grisport boots

   Well, I suppose this is the lower end of the 'outdoor transport' spectrum...

   Liked On: 11-07-2022, 08:00 AM

7. 
   veitnamcam liked post by No.3 On thread : Bullet shockwaves

   The mechanism is plastic deformation of metals, it's a similar (in effect) process to cold drawing alloy cylinders with a massive press pushing onto a disc of ali alloy. The pressure gets to a point...

   Liked On: 11-07-2022, 01:43 AM

8. 
   Micky Duck liked post by No.3 On thread : Is my scope ruined

   Helium isn't a long term thing - it's notoriously hard to keep behind a seal as the molecule size is tiny. That's why they normally use argon as the purge gas - it's a much bigger particle size so...

   Liked On: 10-07-2022, 09:18 PM

9. 
   Moa Hunter liked post by No.3 On thread : Bullet shockwaves

   The mechanism is plastic deformation of metals, it's a similar (in effect) process to cold drawing alloy cylinders with a massive press pushing onto a disc of ali alloy. The pressure gets to a point...

   Liked On: 10-07-2022, 05:36 AM

10. 
    CBH Australia liked post by No.3 On thread : Is my scope ruined

    Was about to say the same thing as m101a1, but thought I's better just read to the bottom haha... Dry internals is the key, doesn't matter if the thing is gassed on argon nitrogen or whatever in...

    Liked On: 09-07-2022, 11:26 PM

11. 
    Micky Duck liked post by No.3 On thread : Improving 45-70 ammo with a mandrel

    Looks like Revlon just branched out into multi-purpose lipstick ammo... On the subject of .45-70, this is definitly overthinking it in my book. .45-70 isn't a target round, so the need for 1/4"...

    Liked On: 09-07-2022, 10:37 PM

12. 
    veitnamcam liked post by No.3 On thread : New Hilux Fuel Consumption

    Yeah it's the hills and the corners that stuffs the fuel economy. Need to get onto those Green bastards and get them to campaign for flat straight roads!!!

    Liked On: 09-07-2022, 10:30 PM

13. 
    dannyb liked post by No.3 On thread : All in the trigger.....

    If he's used to the 2T trigger pull - make a point of telling him to actively think about the trigger pull every tinme he goes to shoot the thing so he doesn't touch off early 'in the moment'. Good...

    Liked On: 09-07-2022, 06:38 PM

14. 
    Moa Hunter liked post by No.3 On thread : New Hilux Fuel Consumption

    There's a bit more to that equation than that - but the basics of your argument are correct. The issue with a smaller engine like the Nissan 2.3L sewing machine with 16 hair dryers and a...

    Liked On: 09-07-2022, 03:13 PM

15. 
    Moa Hunter liked post by No.3 On thread : Budget Family 4WD

    Those little Japanese 4w4 light trucks are very interesting, not road legal but very capable when given a little stilts job and some slightly bigger feet. A wee bit lacking in grunt (some are only...

    Liked On: 06-07-2022, 03:25 PM

Page 101 of 107 First ... 5187888990919293949596979899100101102103104105106107 Last

• Jump to page: