NO4
Member

199 Likes

Page 4 of 14 First 1234567891011121314 Last

• Jump to page:

1. 
   Nathan F liked post by NO4 On thread : Stags and Bucks 2024

   This fella got the slip on me earlier in the month, Tracked him down last Saturday, wasn't so lucky this time. 249015

   Liked On: 28-04-2024, 11:44 PM

2. 
   Ross Nolan liked post by NO4 On thread : Stags and Bucks 2024

   This fella got the slip on me earlier in the month, Tracked him down last Saturday, wasn't so lucky this time. 249015

   Liked On: 28-04-2024, 11:06 PM

3. 
   Billbob liked post by NO4 On thread : Stags and Bucks 2024

   This fella got the slip on me earlier in the month, Tracked him down last Saturday, wasn't so lucky this time. 249015

   Liked On: 28-04-2024, 09:37 PM

4. 
   Tahr liked post by NO4 On thread : Stags and Bucks 2024

   This fella got the slip on me earlier in the month, Tracked him down last Saturday, wasn't so lucky this time. 249015

   Liked On: 28-04-2024, 09:19 PM

5. 
   Shearer liked post by NO4 On thread : Stags and Bucks 2024

   This fella got the slip on me earlier in the month, Tracked him down last Saturday, wasn't so lucky this time. 249015

   Liked On: 28-04-2024, 09:19 PM

6. 
   Bushman Sam liked post by NO4 On thread : Winter Meat Harvest // Southland Red Deer

   Well done Good video keep em coming, Nice looking country to

   Liked On: 02-09-2023, 11:06 AM

7. 
   mudgripz liked post by NO4 On thread : Cold Bluing.

   I 've used the Birchwood super blue with good results. Follow the instruction's on the bottle. Like NO.3 said Prep is the key and a good degreaser to get all those years of oil. I found warming up...

   Liked On: 29-08-2023, 09:11 PM

8. 
   shananah liked post by NO4 On thread : 26mm Rings?

   couldn't you use 1" rings and run a adjustable hand reamer through them?

   Liked On: 23-07-2023, 08:58 PM

9. 
   erniec liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 19-07-2023, 04:45 PM

10. 
    Billbob liked post by NO4 On thread : Mini excavator centre pivot/swivel help

    I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

    Liked On: 18-07-2023, 10:51 PM

11. 
    Tentman liked post by NO4 On thread : Mini excavator centre pivot/swivel help

    I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

    Liked On: 18-07-2023, 10:25 PM

12. 
    ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

    I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

    Liked On: 18-07-2023, 10:08 PM

13. 
    ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

    use a set of internal calipers to measure your groove diameter set to id then measure with Vernier's. remember to allow for draw as well 229244

    Liked On: 18-07-2023, 09:54 PM

14. 
    Micky Duck liked post by NO4 On thread : No Dice....

    I'd say it was a successful hunt, A new area explored,ya know where to head next time plus any day in the bush is better than being at work

    Liked On: 06-07-2023, 04:36 PM

15. 
    Jhon liked post by NO4 On thread : 303B, Churchill Sporter but what model?

    225718 that little pin,can be made from a bit of wire or small drill bit.

    Liked On: 04-06-2023, 09:26 AM

Page 4 of 14 First 1234567891011121314 Last

• Jump to page: