PERRISCICABA
Member

3749 Likes

Page 19 of 250 First ... 5678910111213141516171819202122232425262728293031323369119 ... Last

• Jump to page:

1. 
   PERRISCICABA liked post by carlhurley On thread : Dillon XL650/550 set-up fans

   only problem with buying a dillon 650 is this happens 92386

   Liked On: 05-08-2018, 05:28 PM

2. 
   PERRISCICABA liked post by Simon On thread : Dillon XL650/550 set-up fans

   I have a Mr Bullet feeder and case feeder on my 650. Can easily do 1000 rounds an hour on it (9mm or 38 super). Well worth the money if you shoot a few rounds. Have the same setup (excluding the...

   Liked On: 05-08-2018, 03:08 PM

3. 
   PERRISCICABA liked post by omegaspeedy On thread : Dillon XL650/550 set-up fans

   Yes I definitely want to feed case and bullet. The Mini Mr bullet is a good starting compromise. I think I'll enjoy reloading as much as shooting the ammo with this machine :D

   Liked On: 04-08-2018, 08:14 PM

4. 
   PERRISCICABA liked post by Tommy On thread : Dillon XL650/550 set-up fans

   stretch has a wee inventory of things that make the 650 go betterer

   Liked On: 04-08-2018, 07:50 PM

5. 
   PERRISCICABA liked post by BeeMan On thread : Gun Porn, show off your new toys

   Talking about new toys, yumyum. Being fitted on my sako carbon light .260...Swarovski DS 5-25 52P 9234592346:cool:

   Liked On: 04-08-2018, 07:03 PM

6. 
   PERRISCICABA liked post by Tahr On thread : How hard do you typically push your loads?

   Thats me too. I load until I get pressure signs and then back off until things look right again. Then fiddle with seating depth until they shoot well. If they don't go fast enough I change powder. I...

   Liked On: 04-08-2018, 06:56 PM

7. 
   PERRISCICABA liked post by mikee On thread : How hard do you typically push your loads?

   This ^^^^ for my 6.5TCU realistically I get 2-3 reloads out of a case before the primer falls out. My brass is all formed from once fired .223 pickups. Some brass lasts longer but I also don't...

   Liked On: 04-08-2018, 06:53 PM

8. 
   PERRISCICABA liked post by winaa On thread : How hard do you typically push your loads?

   I start about the middle and work up until I find a load with the lowest SD with safe pressure, then adjust seating depth to get good accuracy. Job done. Generally this ends up 0.5 to 1 grain...

   Liked On: 04-08-2018, 06:50 PM

9. 
   PERRISCICABA liked post by Frogfeatures On thread : How hard do you typically push your loads?

   We must be twins ! :thumbsup:

   Liked On: 04-08-2018, 06:49 PM

10. 
    PERRISCICABA liked post by gadgetman On thread : How hard do you typically push your loads?

    My main criteria is accuracy and I find a node that gives the best result. I don't chase single hole loads with my budget sporting rifles. I could probably get them better but I know there is little...

    Liked On: 04-08-2018, 06:48 PM

11. 
    PERRISCICABA liked post by omegaspeedy On thread : Dillon XL650/550 set-up fans

    9234392344Just picked up my new Dillon XL650 and set it up on my tiny work table that I drag out from the garage and load in the living room. What a fantastic machine! Produced 300rds in an hour as...

    Liked On: 04-08-2018, 06:41 PM

12. 
    PERRISCICABA liked post by sako75 On thread : Photos your proud of -not just hunting

    Not sure if I’m proud of it. Peeled a mandarin for our little fella as vitamin C as both kids have flu and fever Maybe Toby was watching 92227

    Liked On: 02-08-2018, 01:53 PM

13. 
    PERRISCICABA liked post by Ryan_Songhurst On thread : Gun Porn, show off your new toys

    92096 Bit heavier than my finnlight but wasn't bought to be a real lightweight, bought to be a bit of a basher that can do it all, hunt, shoot steel etc to save the barrel burners

    Liked On: 31-07-2018, 08:22 PM

14. 
    PERRISCICABA liked post by Ryan_Songhurst On thread : Gun Porn, show off your new toys

    Bought this off Dreamer a week or two back, T3 in 6.5x55, DPT suppressor, Southfort Labs NZ Hunter carbon stock, have just put a VX5 on it in Talleys and added Atlasworks alloy bottom metal and bolt...

    Liked On: 31-07-2018, 07:54 PM

15. 
    PERRISCICABA liked post by Danny On thread : Photos your proud of -not just hunting

    Tarawera https://uploads.tapatalk-cdn.com/20180728/dd84e802463e90c3b1d2259fd981674d.jpg Kaikōura https://uploads.tapatalk-cdn.com/20180728/3a1b020d7bd07b8da8c1b7ba2ad7a6e9.jpg Kaingaroa today in...

    Liked On: 28-07-2018, 08:17 PM

Page 19 of 250 First ... 5678910111213141516171819202122232425262728293031323369119 ... Last

• Jump to page: