PipIstrelle
Member

59 Likes

Page 2 of 4 First 1234 Last

• Jump to page:

1. 
   PipIstrelle liked post by grandpamac On thread : Shoulder Bump Advice

   Greetings, The tight spot on the shoulder in the chamber may not be where your comparator is measuring so go with the measurement where the case chambers freely. There is one thing to watch on...

   Liked On: 08-04-2023, 08:43 PM

2. 
   PipIstrelle liked post by bluebaiter222 On thread : NZFS ammunition article by Lynn Harris

   Above in the flesh.Along with a variety of ammo from my NZFS days220044220043

   Liked On: 03-04-2023, 12:04 AM

3. 
   PipIstrelle liked post by caberslash On thread : NZFS ammunition article by Lynn Harris

   Hi all, Found this article which I thought best to reproduce here, original was scanned from an NZ Cartridge Collectors (found here: https://forum.cartridgecollectors.or...hester/5468/11) hope you...

   Liked On: 03-04-2023, 12:03 AM

4. 
   PipIstrelle liked post by Kelton On thread : making the change from 223 to 6.5grendel (maybe even 6mm arc?)

   Tikka have changed their. 243 to 8 twist

   Liked On: 30-03-2023, 08:44 AM

5. 
   PipIstrelle liked post by Micky Duck On thread : Can I fire form with an action and dies like this I'm

   So if you already have tools to cut chamber...just cut one in a lump of steel with required bits...nah scratch that.make chamber inserts for bakail.only needs to be die length.job done

   Liked On: 29-03-2023, 02:12 AM

6. 
   PipIstrelle liked post by cambo On thread : Suppressor cleaning

   Robbie told me to never even attempt to clean 1 of his. So I never have. Never been problem. 1 of my suppressors has had excess of 10k .22lr subs thru it...prob more actually the more I think...

   Liked On: 24-03-2023, 05:23 PM

7. 
   PipIstrelle liked post by andyanimal31 On thread : Thoughts on these binos?

   I have owned and used many different range finding binos. I currently run the sig 3000 bdx. Value for money is huge as it has applied ballistics lite installed as well. Good glass a powerfull and...

   Liked On: 24-03-2023, 09:20 AM

8. 
   PipIstrelle liked post by gimp On thread : making the change from 223 to 6.5grendel (maybe even 6mm arc?)

   6CM also performs more or less equivalent to .243 and has 1:8 as a factory twist by default, and there is good factory ammo available - it just doesn't seem to have widely caught on like 6.5CM

   Liked On: 23-03-2023, 07:37 PM

9. 
   PipIstrelle liked post by gimp On thread : making the change from 223 to 6.5grendel (maybe even 6mm arc?)

   A .243 will smoke the 6mmARC with handloads and a 1:8 twist - i.e. all 4 book max loads listed by ADI are ~3050fps with a 108gr ELDM. It's cool that the new Remingtons come with 1:8, makes .243 great...

   Liked On: 23-03-2023, 09:51 AM

10. 
    PipIstrelle liked post by kruza On thread : Recommended air rifle & scope for possum / rabbits

    Any pcp rifle has to be on a fal. Pcp pistols don't.

    Liked On: 16-03-2023, 02:19 AM

11. 
    PipIstrelle liked post by mattstr On thread : Ballistics app for using a Swarovski z5

    Thanks again for all your help. Have been out and validated all my data. Checked at a few different ranges between 300- 500 and absolutely spot on. Bags are packed and into the hills this afternoon.

    Liked On: 12-03-2023, 11:02 PM

12. 
    PipIstrelle liked post by mattstr On thread : Ballistics app for using a Swarovski z5

    Thanks I’ve checked out both apps and have ended up going with strelock. Providing the rain stays away Il hit the range tonight and validate and see how everything’s looking before I go even more...

    Liked On: 10-03-2023, 06:47 AM

13. 
    PipIstrelle liked post by TeRei On thread : Case lengthening when bump sizing

    It is called cordial discussion. Reloading is like guns...zillions of options.

    Liked On: 09-03-2023, 11:00 PM

14. 
    PipIstrelle liked post by zeropak On thread : Pressure signs with factory ammo

    Brand new rifle so carbon/copper buildup will not be the issue. Not the ammo because the milder Fiocchi was giving the same pressure signs. Good point regarding the edges of the ejector holes but the...

    Liked On: 04-03-2023, 09:43 PM

15. 
    PipIstrelle liked post by Micky Duck On thread : Case lengthening when bump sizing

    I also provided one of them..better than thousand words things LOL... AGREE to disagree.

    Liked On: 04-03-2023, 09:40 PM

Page 2 of 4 First 1234 Last

• Jump to page: