Puffin
Member

939 Likes

Page 13 of 63 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by Puffin On thread : The dinner plate challenge

   So can I clarify please? It is a plate diameter based on one's assessment of the kill-zone of the target species (6" say for deer), and the first cold bore shot only, and from a rifle assumed to...

   Liked On: 25-06-2022, 04:39 PM

2. 
   2post liked post by Puffin On thread : The dinner plate challenge

   So can I clarify please? It is a plate diameter based on one's assessment of the kill-zone of the target species (6" say for deer), and the first cold bore shot only, and from a rifle assumed to...

   Liked On: 25-06-2022, 03:26 PM

3. 
   timattalon liked post by Puffin On thread : The dinner plate challenge

   So can I clarify please? It is a plate diameter based on one's assessment of the kill-zone of the target species (6" say for deer), and the first cold bore shot only, and from a rifle assumed to...

   Liked On: 25-06-2022, 03:10 PM

4. 
   Moa Hunter liked post by Puffin On thread : Could be bad news

   Here is a cut & paste from Google Earth that gives a better idea of where the existing road cuts up to attain the ridgeline. An alternative to reach the upper paddock and rejoin the remaining road...

   Liked On: 31-05-2022, 08:23 PM

5. 
   LarryB liked post by Puffin On thread : Could be bad news

   Here is a cut & paste from Google Earth that gives a better idea of where the existing road cuts up to attain the ridgeline. An alternative to reach the upper paddock and rejoin the remaining road...

   Liked On: 31-05-2022, 06:02 PM

6. 
   XR500 liked post by Puffin On thread : Could be bad news

   Here is a cut & paste from Google Earth that gives a better idea of where the existing road cuts up to attain the ridgeline. An alternative to reach the upper paddock and rejoin the remaining road...

   Liked On: 31-05-2022, 04:22 PM

7. 
   veitnamcam liked post by Puffin On thread : Could be bad news

   Yes

   Liked On: 31-05-2022, 12:01 PM

8. 
   Speill liked post by Puffin On thread : Show me your knives

   All thoughts of more knife purchasing put on hold until something becomes available in CPM-Magnacut that takes my fancy.

   Liked On: 20-05-2022, 11:28 PM

9. 
   Dazzh liked post by Puffin On thread : Confusing pressure signs

   The majority of new 6.5x47 Lapua brass have given me stiff extraction with loads a number of grains below the eventual maximum. This went away after applying one of two fixes; either annealing the...

   Liked On: 18-04-2022, 08:21 PM

10. 
    veitnamcam liked post by Puffin On thread : Confusing pressure signs

    The majority of new 6.5x47 Lapua brass have given me stiff extraction with loads a number of grains below the eventual maximum. This went away after applying one of two fixes; either annealing the...

    Liked On: 18-04-2022, 08:00 PM

11. 
    Micky Duck liked post by Puffin On thread : Confusing pressure signs

    The majority of new 6.5x47 Lapua brass have given me stiff extraction with loads a number of grains below the eventual maximum. This went away after applying one of two fixes; either annealing the...

    Liked On: 18-04-2022, 06:43 PM

12. 
    paremata liked post by Puffin On thread : . 284 Winchester

    Yes, a larger diameter neck may offer a possible work-around if you are prepared to arrange your sizing gear to partially size the necks. This has often been discussed on here but perhaps is not...

    Liked On: 16-04-2022, 11:19 AM

13. 
    rugerman liked post by Puffin On thread : Trailer recommendations

    Worth mentioning that if going with the typical 8' x 4' size, then it's helpful to have the trailer dimensioned to accept an imperial 8ft x 4ft (2440mm x 1220mm) floor sheet. That way all the...

    Liked On: 01-03-2022, 06:59 PM

14. 
    25/08IMP liked post by Puffin On thread : Trailer recommendations

    Worth mentioning that if going with the typical 8' x 4' size, then it's helpful to have the trailer dimensioned to accept an imperial 8ft x 4ft (2440mm x 1220mm) floor sheet. That way all the...

    Liked On: 01-03-2022, 06:57 PM

15. 
    grandpamac liked post by Puffin On thread : 30-06

    The difference between 13.5" and 20" barrels chambered in .308Win is 200-250ft/sec The difference between a .308win and 30-06 is 100-150ft/sec

    Liked On: 07-02-2022, 09:18 AM

Page 13 of 63 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: