r87mm
Member

96 Likes

Page 5 of 7 First 1234567 Last

• Jump to page:

1. 
   r87mm liked post by Wingman On thread : 308 twist rate

   My .338 Whispers ran 1-9" twist Shilen and trueflite barrels shooting 300gr SMKs and 300gr Berger hybrids at 1040fps MV. They were still perfectly stable and grouping well with round holes at...

   Liked On: 01-08-2020, 07:59 PM

2. 
   r87mm liked post by Tasbay On thread : Supressor design question

   143934 Just off centre the barrel. 44mag and PVC with alloy plate baffles. Don`t over think it.

   Liked On: 02-07-2020, 08:19 PM

3. 
   r87mm liked post by 2post On thread : Any Diesel or tractor mechs on here?

   Do you have a compressor, I have just done a cylinder head on my mates land Cruiser, I have an adapter that fits in most glow plugs and a few for spark plugs you can borrow. You simply put compressed...

   Liked On: 28-06-2020, 08:49 PM

4. 
   r87mm liked post by Micky Duck On thread : Sunday morning wander take TWO.

   well I turned 48 yesterday.....and being the first free day since lockdown is over I set alarm for 04;30 and got the gear ready for a cracking start.... untill alarm went off.got turned off and...

   Liked On: 07-06-2020, 05:37 PM

5. 
   r87mm liked post by Philipo On thread : RIP Robbie Tiffen

   After a conversation with a couple of guys tonight, just thought I'd remind everyone that you don't really appreciate people until they're gone, their talents & skill should never be forgotten.

   Liked On: 06-06-2020, 07:41 PM

6. 
   r87mm liked post by Boaraxa On thread : A good calibre on pigs

   Avoid 223 , tits on a bull when it comes to shooting pigs reliably , seen a good few fuckups with 223 vs boars , I carted a sawn off bolt action 12g around for years or a 3030 but they were for...

   Liked On: 01-06-2020, 11:45 AM

7. 
   r87mm liked post by stug On thread : 7mm rem mag tahr loads

   The go to load with a 162 a-max eld-m eld-x type projectile is 71-72gr 2217 or 72-74gr 2225. Magnum primer case won’t matter much. I also ran a 160accubond with 1 grain less powder.

   Liked On: 25-05-2020, 07:34 PM

8. 
   r87mm liked post by Wingman On thread : Sierra & Hornady bullet sections

   123gr 6.5mm Hornady SST 138816 Noslers range Left-to-right Partition, Ballistic Tip, AccuBond, E-Tip 138817

   Liked On: 06-05-2020, 07:18 PM

9. 
   r87mm liked post by Rushy On thread : Barrel length vs speed

   The reduced length of the barrel means that the expanding gases from the ignition of the powder have less time to drive the projectile forward so therefor the projectile will be travelling slower...

   Liked On: 01-05-2020, 07:35 AM

10. 
    r87mm liked post by Tikka7mm08 On thread : so.. solar charging.

    I got this epak solaroll a few years ago. Team it with a portable battery pack or direct into device. Came with a couple of led usb lights that run on nothing and can light a hut up for hours. I...

    Liked On: 12-04-2020, 10:42 AM

11. 
    r87mm liked post by Wingman On thread : Neck turning - School me...

    Save yourself the time, brass, money and effort and just go get the chambers neck opened up to no turn specs.

    Liked On: 12-04-2020, 10:34 AM

12. 
    r87mm liked post by Seventenths On thread : 6x45 Rem barrel

    Well, finally took the plunge for a 6x45 of my own... taken 25 years to do it but I'm there. I first got keen on the cartridge after reading a Rod & Rifle magazine which planted a seed and then...

    Liked On: 09-04-2020, 07:21 PM

13. 
    r87mm liked post by grandpamac On thread : Cratered Primer

    Greetings Again, I sure would not be in any hurry to meddle with any load that shoots that well and especially not based on the dubious art of reading primer appearance. I suggest that once the...

    Liked On: 08-04-2020, 06:36 PM

14. 
    r87mm liked post by craigc On thread : Home Arrest Relief Two - Hits and Misses Volume Two

    I'm on leave so I thought I'd make another video to help you pass the time and to remind myself how luck I am to be able to hunt in this country with so many wonderful people. Kia Kaha - this...

    Liked On: 07-04-2020, 09:33 PM

15. 
    r87mm liked post by Preacher On thread : Self isolation gun projects

    Probably a bit late but if you have a stock with a really tough varnish, don't try sanding it immediately (or use paint stripper). Those thin flexible $2 shop paint scraper type dealies with the...

    Liked On: 27-03-2020, 04:01 PM

Page 5 of 7 First 1234567 Last

• Jump to page: