I have a g1 and fire formed new 3030 to 7-30. Tried patches but didn't work great although I should have experimented more and most likely it would have. Instead I annealed the new brass then through...
Liked On: 21-08-2020, 04:11 PM
Yeah I inherited it from who was to be my father in law. I take it as a just incase when walking rifle and make an attempt at least once a year to shot an animal out of respect for him with it I...
Liked On: 21-08-2020, 04:11 PM
Talking to his best mate he said he was an awesome shot with his old 3oh but not so flash in the beginning with the contender. He was a tall man probably 6'2"ish and the contender being so small...
Liked On: 21-08-2020, 03:54 PM
Had a 4x40 wide field Carton brand scope I brought brand new with my first 22 in 1987ish. It was a great scope and ended up on a 223 until I sold it. My old next door neighbor had the 3-9 version...
Liked On: 27-07-2020, 09:28 PM
Had a 4x40 wide field Carton brand scope I brought brand new with my first 22 in 1987ish. It was a great scope and ended up on a 223 until I sold it. My old next door neighbor had the 3-9 version...
Liked On: 27-07-2020, 07:03 PM
Had a 4x40 wide field Carton brand scope I brought brand new with my first 22 in 1987ish. It was a great scope and ended up on a 223 until I sold it. My old next door neighbor had the 3-9 version...
Liked On: 27-07-2020, 06:48 PM
You have a center fire. The 12 gauge. Solids good to 100+ a bit more. Semi option and no boar shield will stop those ounce loads. If you can line up 3 or 4 pigs it will go through them all. No 223...
Liked On: 02-06-2020, 08:38 AM
Maybe .3-.5 gn over but I'd inspect a few then fire them and re inspect. Could be from load development or near max and the odd one with .1-.2 more than others. As for the craters that is the same...
Liked On: 08-04-2020, 10:25 PM
Maybe .3-.5 gn over but I'd inspect a few then fire them and re inspect. Could be from load development or near max and the odd one with .1-.2 more than others. As for the craters that is the same...
Liked On: 08-04-2020, 06:24 PM
Leave digger where it is. It's to small to be of help. Usually when trying to get off on those angles with a drop off digger ends up down the bank upside down with a hurt operator of stuck half way...
Liked On: 02-03-2020, 10:04 AM
Leave digger where it is. It's to small to be of help. Usually when trying to get off on those angles with a drop off digger ends up down the bank upside down with a hurt operator of stuck half way...
Liked On: 27-02-2020, 10:05 PM
Sounds like something is a little worn and a gunsmith job. Before it goes that way I'd just check by cleaning the bolt thoroughly with brake clean and trying it incase it's a bit gummed up inside. If...
Liked On: 13-02-2020, 12:07 PM
Sounds like something is a little worn and a gunsmith job. Before it goes that way I'd just check by cleaning the bolt thoroughly with brake clean and trying it incase it's a bit gummed up inside. If...
Liked On: 13-02-2020, 10:58 AM
Talk to Kiwi Greg. As above 180 eld or berger 180. 7mag 2900-3000ish give or take. Your barrel twist is boarder line and will show at distance more than close. Just because it's stable at 1000...
Liked On: 13-01-2020, 07:13 PM
Talk to Kiwi Greg. As above 180 eld or berger 180. 7mag 2900-3000ish give or take. Your barrel twist is boarder line and will show at distance more than close. Just because it's stable at 1000...
Liked On: 13-01-2020, 07:06 PM