R93
Member

3579 Likes

Page 142 of 239 First ... 4292128129130131132133134135136137138139140141142143144145146147148149150151152153154155156192 ... Last

• Jump to page:

1. 
   R93 liked post by Cyclops On thread : WTF

   The article quotes police saying the FAL holders in question can expect to lose their FAL. So they should, as they've also transported a loaded firearm. Idiots.

   Liked On: 22-01-2016, 02:40 PM

2. 
   R93 liked post by stug On thread : WTF

   Gunworks has a sign at the door stating any bolt actions must have the bolts removed and semis and lever actions must have the actions opened. I expect they have the sign for a reason.

   Liked On: 22-01-2016, 02:40 PM

3. 
   R93 liked post by seano On thread : Picatinny Rail Thingy

   My quick Butchered mount attempt #1 I cut off the rings Then drilled a couple "Wonky holes" ... And I have ver1.0 I'll put bit black marker to cover up the steel Will do the job ,will...

   Liked On: 22-01-2016, 01:24 PM

4. 
   R93 liked post by Beavis On thread : NZP have published their first update on their Firearms review...

   This line here "For example there are three principle problems which are part of a wider issue about whether or not the distinction between MSSAs and other semiautomatics firearms (rifles and...

   Liked On: 22-01-2016, 12:54 AM

5. 
   R93 liked post by Kscott On thread : Great article on rimfire resizing and bullet comparisons

   http://www.rimfirecentral.com/rfcftp/pdfs/resizing-project.pdf These guys have been dealing with rimfire shooting for years, testing $$ cost of ammo vs resizing dies on cheap ammo vs...

   Liked On: 21-01-2016, 11:40 AM

6. 
   R93 liked post by Nibblet On thread : radar detector.

   Not in a 50 area. ....??

   Liked On: 21-01-2016, 11:17 AM

7. 
   R93 liked post by gadgetman On thread : US Firearm Industries under attack!!!!!!!!

   Should be under the Joke section. Marlin I believe are now owned my Remington and are being produced from the Remington factories. If Marlin was shutting shop then so would Remington. And who in...

   Liked On: 21-01-2016, 10:39 AM

8. 
   R93 liked post by Smiddy On thread : The NZ balloting system?

   3m with 110hp engine Sent from my iPhone using Tapatalk

   Liked On: 17-01-2016, 08:43 PM

9. 
   R93 liked post by Nibblet On thread : Hey Admins, Alonzo isn't commercial

   Like it says above, Alonzo isn't a commercial entity. He's just a dude who has acquired a lot of gear in pursuit of his hobby and has now seen the light that blaser is where it's at so is selling...

   Liked On: 16-01-2016, 09:01 PM

10. 
    R93 liked post by Smiddy On thread : The NZ balloting system?

    I don't tend to like foreign hunters getting into place where im not allowed because of the size of there wallet, I also don't like foreign hunters being able to ballot for the same areas as a kiwi...

    Liked On: 16-01-2016, 07:03 PM

11. 
    R93 liked post by stug On thread : My 260AI Load Development Begins

    Possibly, once you have a load with promise at 100, then try 300. Some loads that group OK at 100 group even better at 300 plus. (ie 1" at 100 but 2" at 300) I can't ( and I don't think anyone else...

    Liked On: 16-01-2016, 02:33 PM

12. 
    R93 liked post by Tikka7mm08 On thread : My 260AI Load Development Begins

    Start a new 243 thread fellas.

    Liked On: 16-01-2016, 12:49 PM

13. 
    R93 liked post by Tommy On thread : Policeman shoots himself in foot

    It fits everything that seemed shaky about the situation. The smell of powder at street level, the implausible interval between shots, everyone was looking everywhere around them for the shooter, why...

    Liked On: 15-01-2016, 04:52 PM

14. 
    R93 liked post by On thread : Policeman shoots himself in foot

    The most important ingredient you need for a fuck up is a human

    Liked On: 15-01-2016, 01:50 PM

15. 
    R93 liked post by On thread : die problem?

    got some lee rgb dies ran the cases through them didnt get any problems

    Liked On: 15-01-2016, 11:43 AM

Page 142 of 239 First ... 4292128129130131132133134135136137138139140141142143144145146147148149150151152153154155156192 ... Last

• Jump to page: