rewa
Member

3317 Likes

Page 22 of 222 First ... 8910111213141516171819202122232425262728293031323334353672122 ... Last

• Jump to page:

1. 
   rewa liked post by andyanimal31 On thread : friends asking how much for load development

   Hmm, I have just done a quick work out for a 45g load. Primer at .25c powder at 63c projectile at $1.10. $1.98 with with out labour's. Then if your going through neck cleaning induction annealing...

   Liked On: 21-08-2023, 09:07 PM

2. 
   rewa liked post by stug On thread : friends asking how much for load development

   Double check the legislation to make sure you don’t need a dealers licence for it.

   Liked On: 21-08-2023, 09:05 PM

3. 
   rewa liked post by STC On thread : friends asking how much for load development

   1k??? including 50 rounds and 4 range visits? and after thst 1$ per round? jesus youre cheap! calculate the time you will have to spend. and your hourly rate. including allowance to get to range...

   Liked On: 21-08-2023, 09:04 PM

4. 
   rewa liked post by Kelton On thread : friends asking how much for load development

   I think theirs a joker in tauranga charging about $500 for load d then maybe abit more than a dollar around $1.50 . Its a timly beast and I no your results are spot on so if you happy with that run...

   Liked On: 21-08-2023, 09:03 PM

5. 
   rewa liked post by Puffin On thread : tight closing the bolt

   I've found that forming the so-called "false shoulder" by going up just one calibre has never been sufficient. Grandpamac's use of 35-cal for .280 would do the job, though the brass in the necks is...

   Liked On: 21-08-2023, 08:50 PM

6. 
   rewa liked post by zimmer On thread : tight closing the bolt

   Nah MD he's talking about lifting the case up in the shellholder using a shim. Depends upon some slack being present. Some brands of shellholders have more slack than others. The easiest non fiddly...

   Liked On: 21-08-2023, 08:49 PM

7. 
   rewa liked post by muka88 On thread : tight closing the bolt

   I put the spacer between the bottom of the case and the shell holder to get the case deeper into the sizing die Micky Duck

   Liked On: 21-08-2023, 08:49 PM

8. 
   rewa liked post by Bill999 On thread : tight closing the bolt

   I found that out the hard way mate but its great to have it confirmed I was necking up to 30 cal after that then back down to 7mm but it wasnt enough only about 3 out of 30 blew primers but...

   Liked On: 21-08-2023, 08:48 PM

9. 
   rewa liked post by grandpamac On thread : tight closing the bolt

   Greetings Bill999, Making .280 Rem brass out of .270 or .30-06 cases is not as simple as making 7mm-08 cases out of .308 cases. The .280 Rem is over 1mm (0.050") longer to the shoulder than .270 or...

   Liked On: 21-08-2023, 08:47 PM

10. 
    rewa liked post by dannyb On thread : tight closing the bolt

    "FLS" full length sizing die :thumbsup: The error Shane made was thst his FLS die wasn't set up correctly so it wasn't sizing the case all the way to the bottom, therefore leaving his once fired...

    Liked On: 21-08-2023, 08:46 PM

11. 
    rewa liked post by Gibo On thread : tight closing the bolt

    Bit of forum bromance :thumbsup:

    Liked On: 21-08-2023, 08:45 PM

12. 
    rewa liked post by buell984 On thread : tight closing the bolt

    Thanks everyone for sharing ur experience and knowledge with me, and with the help of a treasured friend dannyb problem has been sorted. Setting up of die properly was the cause, one i had...

    Liked On: 21-08-2023, 08:45 PM

13. 
    rewa liked post by Micky Duck On thread : tight closing the bolt

    what is the new rifle???? I had a BLR that nearly drove me nuts with same issue you desribing....I would load 40 rounds all the same and 15 would chamber fine,15 tightly and 10 not at all....by...

    Liked On: 21-08-2023, 08:43 PM

14. 
    rewa liked post by Bos On thread : tight closing the bolt

    This is definitely a problem often overlooked. If you cant get a small base die, then giving the web of the case a rub with fine emery paper will overcome the problem

    Liked On: 21-08-2023, 08:43 PM

15. 
    rewa liked post by Bill999 On thread : tight closing the bolt

    I found quite a few problems making brass out of 270/30-06 to fit my 280 rem one even blew the plastic bolt shroud off my tikkas bolt now I just buy the proper headstamped stuff almost put me...

    Liked On: 21-08-2023, 08:42 PM

Page 22 of 222 First ... 8910111213141516171819202122232425262728293031323334353672122 ... Last

• Jump to page: