rewa
Member

3317 Likes

Page 44 of 222 First ... 303132333435363738394041424344454647484950515253545556575894144 ... Last

• Jump to page:

1. 
   rewa liked post by 7mm Rem Mag On thread : Rifle and Optics Snobs

   Tha only problem is you just did ha ha

   Liked On: 03-10-2022, 09:24 AM

2. 
   rewa liked post by LMcNab On thread : Rifle and Optics Snobs

   My gear is far too good for me to lower myself to contributing to this thread.

   Liked On: 03-10-2022, 09:24 AM

3. 
   rewa liked post by Ned On thread : rifle change / load/ no bumps etc

   Swap another scope onto it. Make sure it's the rifle and not the scope playing up. Sent from my SM-A528B using Tapatalk

   Liked On: 03-10-2022, 09:20 AM

4. 
   rewa liked post by dannyb On thread : rifle change / load/ no bumps etc

   Maybe you just had a shit day....it happens

   Liked On: 03-10-2022, 09:18 AM

5. 
   rewa liked post by 199p On thread : rifle change / load/ no bumps etc

   I am going to say the zero stop is set wrong. got to be quite out at 300y with a saum but if it hits at 100y then obviously the gun just isn't for you and i'll take it off your hands

   Liked On: 03-10-2022, 09:18 AM

6. 
   rewa liked post by jakewire On thread : rifle change / load/ no bumps etc

   To miss a whole deer three times at only 300 yards would seem to me to be more that a temperature thing.

   Liked On: 03-10-2022, 09:17 AM

7. 
   rewa liked post by Micky Duck On thread : rifle change / load/ no bumps etc

   now here is a suggestion for you...actually for all of you. when your rifle is sighted in...to your desired ZERO.... put the plurry colimeter/boresighter back on wiggle it around till it settled in...

   Liked On: 03-10-2022, 09:15 AM

8. 
   rewa liked post by Hahn On thread : rifle change / load/ no bumps etc

   Any damage to the crown or suppressor? That could explain a sudden change if everything else has checked out fine.

   Liked On: 03-10-2022, 09:15 AM

9. 
   rewa liked post by GWH On thread : rifle change / load/ no bumps etc

   Very strange indeed to completely miss 3 times at 300 yards, when it had all been bang on. I don't think powder temp or seating depth change would make enough difference to clean miss at just 300...

   Liked On: 03-10-2022, 09:14 AM

10. 
    rewa liked post by Bill999 On thread : rifle change / load/ no bumps etc

    iv also had a different situation where the recticle inside the scope came loose so give things a good shake to see if anything is loose most of the time its just loose bolts or screws

    Liked On: 03-10-2022, 09:14 AM

11. 
    rewa liked post by jakewire On thread : rifle change / load/ no bumps etc

    It is equipment failure without a doubt A 300 yard shot on a deer shoulder is a chip shot. If it helps I have an unopened bottle of RL 26 that I will trade for a Bentley Turbo R, so long as the...

    Liked On: 03-10-2022, 09:13 AM

12. 
    rewa liked post by GWH On thread : rifle change / load/ no bumps etc

    Can do the same thing with a simple boresight, can even do it on the hill if someone suspects they are a turn out on their turret.

    Liked On: 03-10-2022, 09:13 AM

13. 
    rewa liked post by PerazziSC3 On thread : rifle change / load/ no bumps etc

    If the scope has lost its zero I wouldn't trust it again and would send back for a refund

    Liked On: 03-10-2022, 09:11 AM

14. 
    rewa liked post by Larskramer On thread : rifle change / load/ no bumps etc

    yeah mate, have done this. I usually bore sight at 100m before trying to zero a rifle. takes out alot of un necessary rounds

    Liked On: 03-10-2022, 09:11 AM

15. 
    rewa liked post by Hurricane On thread : rifle change / load/ no bumps etc

    When I lived in the US I had access to a 1000 acre property with a nice cleared ride for an electricity line. I shot my .300WM twice there at 500 yards, once in warm weather (about 26C from memory),...

    Liked On: 03-10-2022, 09:10 AM

Page 44 of 222 First ... 303132333435363738394041424344454647484950515253545556575894144 ... Last

• Jump to page: