rewa
Member

3317 Likes

Page 47 of 222 First ... 333435363738394041424344454647484950515253545556575859606197147 ... Last

• Jump to page:

1. 
   rewa liked post by Cigar On thread : Panelbeater narrowly avoids Armageddon

   Tiny car if four rounds of shotgun ammo can fill it up with gunpowder! Some journalist/editor needs to be sacked

   Liked On: 19-08-2022, 10:17 AM

2. 
   rewa liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

   Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

   Liked On: 19-08-2022, 10:17 AM

3. 
   rewa liked post by gundoc On thread : Which 4 guns do I need in NZ?

   You don't need a 7mm and a .308. Your .30/06 would be excellent as your main hunting rifle, but any standard cartridge in the 7mm to .30/06 range is perfectly adequate. If you did need another...

   Liked On: 19-08-2022, 10:11 AM

4. 
   rewa liked post by gundoc On thread : Transiting through Australia with Projectiles

   The only transit place I know where it could be a problem is Singapore. Aussie, no problem but beware of ignorant and officious customs/security staff who may 'try it on'.

   Liked On: 17-08-2022, 02:30 PM

5. 
   rewa liked post by Dicko On thread : Transiting through Australia with Projectiles

   If there in your checked in luggage and its going straight through to NZ should no be a problem as theoretically its not in oz...

   Liked On: 17-08-2022, 02:30 PM

6. 
   rewa liked post by Mooseman On thread : Transiting through Australia with Projectiles

   We are off to Canada in September and I will pick up some projectiles and brass if it's not to dear. I spoke to our local Arms Officer and a permit for projectiles and brass is not required, not...

   Liked On: 17-08-2022, 02:29 PM

7. 
   rewa liked post by 7mmsaum On thread : Hornady Shipment

   It’s just rebranded CCI SV

   Liked On: 17-08-2022, 02:25 PM

8. 
   rewa liked post by SiB On thread : Rewarewa for furniture?

   Google says; “Rewarewa is hard to dry with severe distortion (considerable tangential shrinkage) and cracking, but when dry it is heavy, hard and very wear resistant.” A conversation with a...

   Liked On: 17-08-2022, 02:15 PM

9. 
   rewa liked post by rambo-6mmrem On thread : My 1st Expedition into the world of rust blue

   PaulNZ Makros im not going to out of respect for him as even though he is in the usa he dose make his living selling the stuff and probably doesn't want it all over the web however i had to buy...

   Liked On: 17-08-2022, 02:07 PM

10. 
    rewa liked post by rambo-6mmrem On thread : My 1st Expedition into the world of rust blue

    Done a absolutely insane amount of cold blue jobs in my time and have gotten pretty good at it They look fantastic but the finish wears off in 5 minutes or and very least lightens up Been talking...

    Liked On: 17-08-2022, 02:06 PM

11. 
    rewa liked post by musket On thread : How to bend 40mm copper pipe 180° ?

    Copper to copper joints only need to be clean (no flux) if using silphos. Is that a copper to steel joint at the open end? Copper to mild steel with silphos ( eziflo is better) will need braising...

    Liked On: 17-08-2022, 02:04 PM

12. 
    rewa liked post by 40mm On thread : How to bend 40mm copper pipe 180° ?

    Here you go. I will make a post for the home builds thread when I get some more pictures and progress. 200399 200400

    Liked On: 17-08-2022, 02:02 PM

13. 
    rewa liked post by 40mm On thread : How to bend 40mm copper pipe 180° ?

    The heat exchanger is 1.2m long and 40mm pipe, so wont fit anything else.... I have made a 'rocket stove' which is a very efficient type of fire. It is made from two D size oxygen bottles welded...

    Liked On: 17-08-2022, 02:00 PM

14. 
    rewa liked post by Russian 22. On thread : How to bend 40mm copper pipe 180° ?

    Just use the pre bent piece. most plumbing pipe is hard drawn and requires annealing by getting cherry red and then cooling. Otherwise bending is nigh impossible. unless you have a hard round...

    Liked On: 17-08-2022, 01:58 PM

15. 
    rewa liked post by Marty Henry On thread : How to bend 40mm copper pipe 180° ?

    The sand or plumbers spring method is the classic one. I can remember dad doing this I got to hold the blowlamp to heat the section, the colour changes on the pipe when the flame was on it fascinated...

    Liked On: 17-08-2022, 01:58 PM

Page 47 of 222 First ... 333435363738394041424344454647484950515253545556575859606197147 ... Last

• Jump to page: