rewd
Member

66 Likes

Page 2 of 5 First 12345 Last

• Jump to page:

1. 
   tetawa liked post by rewd On thread : Sytong advice please.

   Hows the 6.5x for scanning? My CFO would require a thinning of assets to offset the purchase,depending on how creative I get with the books.

   Liked On: 08-09-2021, 01:22 PM

2. 
   Chelsea liked post by rewd On thread : Sytong advice please.

   Bored and getting an itchy money finger,money which I don't have according to the financial controller.So doing the right thing and ignoring her and asking you gentlemen.Looking at the Sytong HT 60...

   Liked On: 31-08-2021, 01:56 PM

3. 
   Phil_H liked post by rewd On thread : Sytong advice please.

   Bored and getting an itchy money finger,money which I don't have according to the financial controller.So doing the right thing and ignoring her and asking you gentlemen.Looking at the Sytong HT 60...

   Liked On: 25-08-2021, 04:14 PM

4. 
   Phil_H liked post by rewd On thread : Sytong advice please.

   Hows the 6.5x for scanning? My CFO would require a thinning of assets to offset the purchase,depending on how creative I get with the books.

   Liked On: 25-08-2021, 04:12 PM

5. 
   Pixie Z liked post by rewd On thread : New Baikal 121 Single Shot out

   I have two 18MH both on loan to friends and am having trouble getting them to cough them back up. Cheap,sturdy,shoot well and pack down.Plus if my truck shits an axle I have a couple of spares. The...

   Liked On: 27-11-2020, 11:09 PM

6. 
   outlander liked post by rewd On thread : Today’s F$#k up

   soak with crc/brake clean,wrap the end around a round piece of wood to make a strong handle,2 beefy lads on either end and pull like you were pulling Helen Clarks teeth.

   Liked On: 26-06-2020, 01:33 PM

7. 
   Moa Hunter liked post by rewd On thread : Today’s F$#k up

   soak with crc/brake clean,wrap the end around a round piece of wood to make a strong handle,2 beefy lads on either end and pull like you were pulling Helen Clarks teeth.

   Liked On: 22-06-2020, 10:00 PM

8. 
   Marty Henry liked post by rewd On thread : Drillings/combination guns

   I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

   Liked On: 09-06-2020, 08:29 AM

9. 
   norsk liked post by rewd On thread : Drillings/combination guns

   I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

   Liked On: 09-06-2020, 04:24 AM

10. 
    timattalon liked post by rewd On thread : Drillings/combination guns

    I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

    Liked On: 09-06-2020, 12:27 AM

11. 
    Husky1600 liked post by rewd On thread : Drillings/combination guns

    I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

    Liked On: 08-06-2020, 08:56 PM

12. 
    Ryan_Songhurst liked post by rewd On thread : Drillings/combination guns

    I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

    Liked On: 08-06-2020, 08:42 PM

13. 
    john m liked post by rewd On thread : Drillings/combination guns

    I have one in 7x57R over 12G fun to use,00 in the 12G for tight stuff snap shot,7mm for longer stuff.Also being a Baikal handy if your truck shits an axle.

    Liked On: 08-06-2020, 07:39 PM

14. 
    rugerman liked post by rewd On thread : Gear you wish you kinda wish you never bought..

    Fuck should go to bed starting to see double.Sorry Fellas.

    Liked On: 07-05-2020, 11:52 AM

15. 
    Cordite liked post by rewd On thread : Great article on rimfire resizing and bullet comparisons

    Don't think so. I have the Waltz die and it is very well made. I use it to hollow point CCI standard.Is it worth the time vs cost of CCI factory HP,that depends on what value your time vs the fun...

    Liked On: 20-04-2020, 07:29 PM

Page 2 of 5 First 12345 Last

• Jump to page: