Roarless20
Member

1220 Likes

Page 4 of 82 First 12345678910111213141516171854 ... Last

• Jump to page:

1. 
   Roarless20 liked post by Bhess On thread : Beat sika so far

   A mate and I decided to go for a sika mission into some new country for us the, famed Clement’s mill Rd! Put a big shift in on Tuesday avo in appalling weather walking about 4 hours into an area I...

   Liked On: 11-04-2025, 09:42 PM

2. 
   Roarless20 liked post by hebe On thread : Mongrel stags in mongrel country

   After poring over maps for a fair whack of time and hoping my preferred area of the Northern Ruahines wouldn’t get 1080’d I found out the drop was postponed. I had looked at a series of faces from...

   Liked On: 09-04-2025, 08:35 PM

3. 
   Roarless20 liked post by gimp On thread : 223 on deer

   80 ELDM 220m just behind shoulder exited big red hind 270847 200m through spine (misjudged the range and held for 250m - small yearling red), euthanized with head shot 270849 320m red...

   Liked On: 06-04-2025, 08:30 AM

4. 
   Roarless20 liked post by Stocky On thread : 223 on deer

   77TMK 223 clearly bounced of the red stag but he was kind enough to let my brother pose next to him for a picture. 270864

   Liked On: 06-04-2025, 08:30 AM

5. 
   Roarless20 liked post by gimp On thread : Testing a conventional approach to load development

   Fortunely I've done it for you! No need. Life is simple, pick a good powder from ADI, a quality bullet, put it in good brass with a near max load seated to just short of mag length or something like...

   Liked On: 06-04-2025, 08:15 AM

6. 
   Roarless20 liked post by gimp On thread : Testing a conventional approach to load development

   Okay so I went and shot these this morning. Conditions were good - essentially nil wind, my usual setup shooting at 100m with Atlas bipod & rear bag prone. First, I did the process McNotty...

   Liked On: 05-04-2025, 02:06 PM

7. 
   Roarless20 liked post by Friwi On thread : 7mm PRC brass

   Could they become a solution when the primer pockets are too lose for the federal?

   Liked On: 05-04-2025, 09:42 AM

8. 
   Roarless20 liked post by kiwi303 On thread : The Zero Check Thread

   The 223 on deer thread has urged me to set up an 18' 223 to run on general pest control. I picked up a 8 twist barrel off of a mate recently, cut it back to 18" and have been running the same...

   Liked On: 04-04-2025, 09:51 PM

9. 
   Roarless20 liked post by dannyb On thread : Howa Superlite aluminium bottom metal

   Hell yeah Rob very nice work :cool: perfect fit no trimming needed for my stock. I have torqued mine to 40 inch pounds, I may re asses that once I've bedded it. 271912 271913 271914

   Liked On: 03-04-2025, 09:56 PM

10. 
    Roarless20 liked post by Parky On thread : Stop torch Glare off suppressor

    Take torch to plumbers. Find right size downpipe just long enough to shade the suppressor. If too big cut a slot long ways and wrap tape around until slips on and off torch. Job done

    Liked On: 03-04-2025, 03:01 PM

11. 
    Roarless20 liked post by kukuwai On thread : Stags and Bucks 2025

    I'm with Big bear, discussion for another thread. Well done Tasbay post up as many of those photos as you like[emoji106] Any animal shot with homemade powder and a 50cal ball is a trophy...

    Liked On: 03-04-2025, 08:22 AM

12. 
    Roarless20 liked post by robhughes-games On thread : Tikka aluminium bottom metal

    I've done up a design and machined one as a test. If there's interest in them I can do a batch. Takes the factory mag, will have an alloy mag catch, just using the factory one for test. 6061...

    Liked On: 03-04-2025, 08:20 AM

13. 
    Roarless20 liked post by robhughes-games On thread : Howa Superlite aluminium bottom metal

    It's taken a while, but the superlite bottom metals are coming off the machine. These ones will take the factory mags. The likelihood of doing a blind version is low for now. I've found that the...

    Liked On: 03-04-2025, 08:16 AM

14. 
    Roarless20 liked post by robhughes-games On thread : Howa Superlite aluminium bottom metal

    Turned out quite pretty.271821

    Liked On: 03-04-2025, 08:15 AM

15. 
    Roarless20 liked post by Shearer On thread : Stags and Bucks 2025

    "Improving the gene pool" is just my excuse for not being able to find anything better.

    Liked On: 02-04-2025, 07:49 PM

Page 4 of 82 First 12345678910111213141516171854 ... Last

• Jump to page: