Roarless20
Member

755 Likes

Page 41 of 51 First ... 27282930313233343536373839404142434445464748495051 Last

• Jump to page:

1. 
   Oldbloke liked post by Roarless20 On thread : Pressure signs with factory ammo

   You didn't mention drying the chamber between each two shot and clean cycle. So probably the wet chamber causing issues. I dry mop the chamber and a dry patch down the bore each time I take a rifle...

   Liked On: 05-03-2023, 10:56 AM

2. 
   Cam86NZ liked post by Roarless20 On thread : 6.5 143 ELD-X, are they THE 6.5 hunting bullet?

   You would definitely get more speed from whatever cartridge you are loading for mate. You clearly run your reloads at max to over pressure. Your .260 and 6.5CM running 140+ class pills at 2800fps...

   Liked On: 16-02-2023, 01:00 PM

3. 
   janleroux liked post by Roarless20 On thread : 6.5 143 ELD-X, are they THE 6.5 hunting bullet?

   You would definitely get more speed from whatever cartridge you are loading for mate. You clearly run your reloads at max to over pressure. Your .260 and 6.5CM running 140+ class pills at 2800fps...

   Liked On: 09-02-2023, 06:54 AM

4. 
   hotsoup liked post by Roarless20 On thread : 6.5 143 ELD-X, are they THE 6.5 hunting bullet?

   You would definitely get more speed from whatever cartridge you are loading for mate. You clearly run your reloads at max to over pressure. Your .260 and 6.5CM running 140+ class pills at 2800fps...

   Liked On: 08-02-2023, 08:20 PM

5. 
   Rated M for Magnum liked post by Roarless20 On thread : 6.5 143 ELD-X, are they THE 6.5 hunting bullet?

   I haven't had the 143 eldx fail at close range in my 18" barreled 6.5prc yet. One close shot at a sika stag at 20m that was wounded from a failed 123gr sst @2900fps, which I think hit brush before...

   Liked On: 08-02-2023, 12:58 PM

6. 
   Shearer liked post by Roarless20 On thread : 89gr eld-m 223

   I've just sorted a load in my tikka .223 22". Adi brass, cci 400, 80gr eldm @ 2.435" OAL 24.6gr Ar2206 (old from a .308 target shooters bulk barrel, not sure if it is 2206H) 2900fps Definitely...

   Liked On: 05-02-2023, 08:00 PM

7. 
   caberslash liked post by Roarless20 On thread : How do these Warne Vertical Rings work?

   These are brilliant at crushing scope tubes :thumbsup:

   Liked On: 02-02-2023, 07:46 AM

8. 
   Friwi liked post by Roarless20 On thread : How do these Warne Vertical Rings work?

   These are brilliant at crushing scope tubes :thumbsup:

   Liked On: 01-02-2023, 08:16 PM

9. 
   Barefoot liked post by Roarless20 On thread : How do these Warne Vertical Rings work?

   These are brilliant at crushing scope tubes :thumbsup:

   Liked On: 01-02-2023, 12:32 PM

10. 
    Micky Duck liked post by Roarless20 On thread : Leupold Turret Help

    SikaHuntaa The ball bearing in the hole idea didn't work on my cap as the existing hole is nowhere near '0'. I used a 1.5mm drill bit to drill the hole and then cut off the shank end of the...

    Liked On: 26-01-2023, 04:27 PM

11. 
    SikaHuntaa liked post by Roarless20 On thread : Leupold Turret Help

    SikaHuntaa The ball bearing in the hole idea didn't work on my cap as the existing hole is nowhere near '0'. I used a 1.5mm drill bit to drill the hole and then cut off the shank end of the...

    Liked On: 26-01-2023, 04:18 PM

12. 
    Bill999 liked post by Roarless20 On thread : Leupold Turret Help

    SikaHuntaa The ball bearing in the hole idea didn't work on my cap as the existing hole is nowhere near '0'. I used a 1.5mm drill bit to drill the hole and then cut off the shank end of the...

    Liked On: 26-01-2023, 08:34 AM

13. 
    Moa Hunter liked post by Roarless20 On thread : Leupold Turret Help

    SikaHuntaa The ball bearing in the hole idea didn't work on my cap as the existing hole is nowhere near '0'. I used a 1.5mm drill bit to drill the hole and then cut off the shank end of the...

    Liked On: 25-01-2023, 11:02 PM

14. 
    Nick-D liked post by Roarless20 On thread : Leupold Turret Help

    SikaHuntaa The ball bearing in the hole idea didn't work on my cap as the existing hole is nowhere near '0'. I used a 1.5mm drill bit to drill the hole and then cut off the shank end of the...

    Liked On: 25-01-2023, 10:36 PM

15. 
    6.5 CRD liked post by Roarless20 On thread : Reloading for 6.5 Creed & 300WM - Confirming Research

    Also be aware that you will get apparent pressure signs with any load if the rifle chamber has oil/lube in it or on the brass cases. Make sure you mop out the rifle barrel and chamber when you take...

    Liked On: 18-01-2023, 06:23 AM

Page 41 of 51 First ... 27282930313233343536373839404142434445464748495051 Last

• Jump to page: