Ross Nolan
Member

834 Likes

Page 8 of 56 First 12345678910111213141516171819202122 ... Last

• Jump to page:

1. 
   Ross Nolan liked post by mikee On thread : Photos of your dog

   A Labrador is an essential survival tool as if you are ever attacked by angry food you can "engage the Lab" and will likely survive unscathed!! :D

   Liked On: 20-02-2024, 12:09 PM

2. 
   Ross Nolan liked post by Hokistag On thread : Barrel cleaning

   I run a bore snake through every now and then and aslong as grouping good dont touch it

   Liked On: 20-02-2024, 10:46 AM

3. 
   Ross Nolan liked post by Tahr On thread : Photos of your dog

   She had already had a good tummy full while I was dealing to it. The old Wirehair was never very interested. Labs are something else :)

   Liked On: 20-02-2024, 10:45 AM

4. 
   Ross Nolan liked post by XR500 On thread : Deer Population Growth

   If it makes you feel any better, these two clowns were running around about a hundred m in front of your silage bale bench rest...30 and 31 Jan. at 10am even. Then again, you had quite the...

   Liked On: 19-02-2024, 04:39 PM

5. 
   Ross Nolan liked post by makka On thread : 223 on deer

   That is true, I picked up a box of 73's the other day and the build is progressing slowly 243734

   Liked On: 19-02-2024, 08:00 AM

6. 
   Ross Nolan liked post by Percy Jones On thread : Incline / decline shooting

   pythagoras theorem does have its uses.

   Liked On: 19-02-2024, 07:58 AM

7. 
   Ross Nolan liked post by Hokistag On thread : Incline / decline shooting

   Yer it makes sense now- not a position i have been in before so wasnt schooled on how to deal with it but simple science i guess and good learning curve

   Liked On: 14-02-2024, 09:54 PM

8. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   The butt plate being hollow needs careful sculping to get the fit right into the hollow. Quite a bit of time/patience later it is a nice fit. I like to file the waste wood away from the butt plate...

   Liked On: 13-02-2024, 02:05 PM

9. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   With that done it is now that the shaping lines are drawn in and for the bottom line I mark round the top of the trigger guard. https://i.imgur.com/rg4YT8Hl.jpg Next I mark in the forestock...

   Liked On: 13-02-2024, 02:03 PM

10. 
    Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

    Time now to do the forend tip so a piece of buffalo horn had the face trued up on the grinder belt and cut to length https://i.imgur.com/1x2NFiyl.jpg This piece is barely big enough but with...

    Liked On: 13-02-2024, 02:03 PM

11. 
    Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

    This morning saw the trigger guard settled into place and then the magazine cut off plate was also fitted with the appropriate wood removed to allow it to operate. Slow and methodical with a great...

    Liked On: 13-02-2024, 02:02 PM

12. 
    Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

    With the B/A tight into the inlet the unit can be turned over in the vise and the TG sat in between the fixing ears and lined up with the center mark on the underside of the fore stock and fine...

    Liked On: 13-02-2024, 02:02 PM

13. 
    Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

    First thing toady I drilled 3 10mm holes as a start for the trigger /mag spring assembly and a couple of 20mm and one 24mm holes for the start of the mag well. https://i.imgur.com/yt3DMiVl.jpg ...

    Liked On: 13-02-2024, 02:02 PM

14. 
    Ross Nolan liked post by Gkp On thread : Is the new 7mm PRC a lemon ?

    All barrels shoot different speeds. Hopefully as the cartridge gains traction other companies with enter the market with better quality ammo. For the reloader the 7mm saum does the same thing with...

    Liked On: 13-02-2024, 07:04 AM

15. 
    Ross Nolan liked post by Longrun On thread : Carrying firearm on doc track

    they're

    Liked On: 09-02-2024, 10:08 PM

Page 8 of 56 First 12345678910111213141516171819202122 ... Last

• Jump to page: