rupert
Member

266 Likes

Page 8 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   NZ_noddy liked post by rupert On thread : Rifle Accuracy Facts

   Free download of this seriously good and out of print book. http://storage.dynamic-arms.com/t-class/books/Rifle%20Accuracy%20Facts%20Full%20v1.1.pdf

   Liked On: 22-06-2023, 08:49 AM

2. 
   Pete_D liked post by rupert On thread : Getting a Farm bike road registered ???

   I had a KLX250 revinned about a year ago, after the rego lapsed. It cost a bit over $500 in Christchurch. The bike was in factory condition, without modifications of any sort.

   Liked On: 01-05-2023, 10:30 PM

3. 
   caberslash liked post by rupert On thread : .308 into .243?

   Anneal the neck after sizing. If you anneal before, there is a possibility for the neck to collapse. If you don't anneal afterwards, the necks will crack later. Polish the inside of your resizing die...

   Liked On: 26-02-2023, 07:58 PM

4. 
   Puffin liked post by rupert On thread : .308 into .243?

   Anneal the neck after sizing. If you anneal before, there is a possibility for the neck to collapse. If you don't anneal afterwards, the necks will crack later. Polish the inside of your resizing die...

   Liked On: 26-02-2023, 04:04 PM

5. 
   Shearer liked post by rupert On thread : Trigger CZ452 17 hmr

   Have you tried altering the sear engagement with a bit of aluminium tape around the trigger pivot, and/or tried a couple of ball point pen springs to increase trigger pull weight or a spacer on your...

   Liked On: 30-01-2023, 11:31 AM

6. 
   HG Man liked post by rupert On thread : How to get rid of an old stock?

   Put them in the free column on this site.

   Liked On: 28-01-2023, 06:51 PM

7. 
   300CALMAN liked post by rupert On thread : How to get rid of an old stock?

   Put them in the free column on this site.

   Liked On: 27-01-2023, 09:47 PM

8. 
   Grey Kiwi liked post by rupert On thread : Bought new bino's...good move or bad?

   What I understand from reviews of Chinese binoculars and my own experience with Chinese scopes is, sometimes, very variable build quality. In the production some will be abysmal and others very good...

   Liked On: 01-01-2023, 10:41 AM

9. 
   caberslash liked post by rupert On thread : 7mm rem mag reloading issues

   What kind of stock? What kind of action? How was the bedding checked? Sounds like a bedding issue.

   Liked On: 22-12-2022, 10:04 PM

10. 
    grandpamac liked post by rupert On thread : What are you using for pressure estimation in your handloads.

    A method that I have found to be useful for rear locking actions is to measure. the length of the case over a series of firings of an individual case with a chosen load. If the case stretches (and it...

    Liked On: 14-12-2022, 10:39 AM

11. 
    Micky Duck liked post by rupert On thread : What are you using for pressure estimation in your handloads.

    A method that I have found to be useful for rear locking actions is to measure. the length of the case over a series of firings of an individual case with a chosen load. If the case stretches (and it...

    Liked On: 13-12-2022, 05:21 PM

12. 
    Micky Duck liked post by rupert On thread : 7mm Rem Mag H870 data

    A post from 'Hunting Nut' website quotes Nosler No.5 manual for Nosler 160gr partition and H870: Start load 75.5gr/2982ft/sec Mid load 77.5gr/3047ft/sec Max load 79.5gr/3112ft/sec and Old...

    Liked On: 11-12-2022, 06:05 PM

13. 
    Tedz50 liked post by rupert On thread : 308 accuracy: factory match ammo vs. military ball

    https://rifleshooter.com/2022/11/m24-accuracy-with-m80-ball-ammunition/ A small dose of data, so you know what you might expect.

    Liked On: 27-11-2022, 09:25 PM

14. 
    mudgripz liked post by rupert On thread : 308 accuracy: factory match ammo vs. military ball

    https://rifleshooter.com/2022/11/m24-accuracy-with-m80-ball-ammunition/ A small dose of data, so you know what you might expect.

    Liked On: 27-11-2022, 04:37 PM

15. 
    300CALMAN liked post by rupert On thread : Question: Restoring ( near ) new look to brass

    Wet tumbling with stainless pins will take the tarnish off.

    Liked On: 23-11-2022, 07:32 PM

Page 8 of 18 First 123456789101112131415161718 Last

• Jump to page: