rupert
Member

256 Likes

Page 14 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   rossi.45 liked post by rupert On thread : Bergara B14 rifle

   Fire-cracking - when the cartridge is fired in the barrel chamber a very hot flame follows the bullet down the barrel. The flame erodes the bore of the barrel. If you have a look with a bore-scope...

   Liked On: 27-08-2019, 08:45 AM

2. 
   Sasquatch liked post by rupert On thread : Bergara B14 rifle

   Fire-cracking - when the cartridge is fired in the barrel chamber a very hot flame follows the bullet down the barrel. The flame erodes the bore of the barrel. If you have a look with a bore-scope...

   Liked On: 26-08-2019, 10:49 PM

3. 
   Moa Hunter liked post by rupert On thread : Pressure sign in the single shot

   I found that in the example of a small Martini (224 Hornet chambering) the brass case would stretch if the load was an overload. So, fire a sequence of incrementally increasing loads and measure the...

   Liked On: 22-08-2019, 12:22 AM

4. 
   Nick-D liked post by rupert On thread : Pressure sign in the single shot

   I found that in the example of a small Martini (224 Hornet chambering) the brass case would stretch if the load was an overload. So, fire a sequence of incrementally increasing loads and measure the...

   Liked On: 21-08-2019, 10:09 PM

5. 
   Micky Duck liked post by rupert On thread : Pressure sign in the single shot

   I found that in the example of a small Martini (224 Hornet chambering) the brass case would stretch if the load was an overload. So, fire a sequence of incrementally increasing loads and measure the...

   Liked On: 21-08-2019, 08:58 PM

6. 
   Nesika liked post by rupert On thread : 17 Hornet

   There are threads on the 17 Ackley Hornet and the 17 Hornady Hornet in the past. I have a 17AH built on a BRNO 465. Had it for about 15 years. Excellent cartridge. Relatively easy to load using the...

   Liked On: 07-07-2019, 07:19 PM

7. 
   Mathias liked post by rupert On thread : 17 Hornet

   There are threads on the 17 Ackley Hornet and the 17 Hornady Hornet in the past. I have a 17AH built on a BRNO 465. Had it for about 15 years. Excellent cartridge. Relatively easy to load using the...

   Liked On: 06-07-2019, 11:08 AM

8. 
   jakewire liked post by rupert On thread : 17 Hornet

   There are threads on the 17 Ackley Hornet and the 17 Hornady Hornet in the past. I have a 17AH built on a BRNO 465. Had it for about 15 years. Excellent cartridge. Relatively easy to load using the...

   Liked On: 06-07-2019, 05:57 AM

9. 
   GWH liked post by rupert On thread : 17 Hornet

   There are threads on the 17 Ackley Hornet and the 17 Hornady Hornet in the past. I have a 17AH built on a BRNO 465. Had it for about 15 years. Excellent cartridge. Relatively easy to load using the...

   Liked On: 06-07-2019, 12:51 AM

10. 
    Nugget connaisseur liked post by rupert On thread : Belmont ammo 308 with hornady 150gr SP - Range Report

    It will be very interesting to see your work on the variance between lots.

    Liked On: 02-07-2019, 01:47 PM

11. 
    Moa Hunter liked post by rupert On thread : Oh Bother!

    Take out the decapping assembly from the die. Fill up the case with cerrosafe. Push the case out (in a vice) with a rod through the decapping assembly hole with a steel rod. I got a case stuck in the...

    Liked On: 02-06-2019, 05:46 PM

12. 
    NZ_noddy liked post by rupert On thread : Oh Bother!

    Take out the decapping assembly from the die. Fill up the case with cerrosafe. Push the case out (in a vice) with a rod through the decapping assembly hole with a steel rod. I got a case stuck in the...

    Liked On: 02-06-2019, 12:23 PM

13. 
    chainsaw liked post by rupert On thread : building a 6.506 what do i need to know

    Lowest cost: use once fired 270Win, necked down in the full length 6.5-06 die to just fit your rifle chamber and then fire form using the COW method.

    Liked On: 13-05-2019, 02:44 PM

14. 
    mopheadrob liked post by rupert On thread : Closer... closer... CLOSER... (warning - long story!)

    Really enjoyed your story.

    Liked On: 25-03-2019, 11:51 PM

15. 
    tetawa liked post by rupert On thread : Re-sizing Issues-Tight Chamber?

    The lowest cost option to increase the sizing effect of your current press/dies is to file a little off the top of the shell holder. It is better if this process is an incremental one with a resized...

    Liked On: 24-03-2019, 11:30 AM

Page 14 of 18 First 123456789101112131415161718 Last

• Jump to page: