sneeze
Member

2225 Likes

Page 53 of 149 First ... 33940414243444546474849505152535455565758596061626364656667103 ... Last

• Jump to page:

1. 
   Micky Duck liked post by sneeze On thread : AIMNZ ENGINEERING

   Flight school? After eating the last red crayon ...........at flight school? First week of basic after mistaking the red tip on the training ammo for a crayon? Ah to many optiions.. I give...

   Liked On: 11-12-2018, 09:24 PM

2. 
   dannyb liked post by sneeze On thread : AIMNZ ENGINEERING

   Complete spastic must be to corrosive, Id try mostly spastic for the repair. For future reference Id make sure the complete spastic is locked away and only bought out under supervision.

   Liked On: 11-12-2018, 08:51 PM

3. 
   R93 liked post by sneeze On thread : AIMNZ ENGINEERING

   Complete spastic must be to corrosive, Id try mostly spastic for the repair. For future reference Id make sure the complete spastic is locked away and only bought out under supervision.

   Liked On: 11-12-2018, 08:40 PM

4. 
   Tribrit liked post by sneeze On thread : Remington 700 Sako and M16 extractor conversions

   So ... copper crushing is useless,brass to variable,strain gauge.. well thats no good,chronys? na... most arnt reliable ,maufactures of loading manuals use the pre mentiond so chuck them in the bin...

   Liked On: 05-12-2018, 08:28 PM

5. 
   Moa Hunter liked post by sneeze On thread : 6.5 cal addicts

   Over a labradar my 24" barreled 6.5x 284 is at 2950 with the 140 EH and 2225. The 143 elxd had a good node at 3000 with RL 23 but the case head expansion on the Lapua brass was a little more than...

   Liked On: 05-12-2018, 12:34 PM

6. 
   Mathias liked post by sneeze On thread : 6.5 cal addicts

   Over a labradar my 24" barreled 6.5x 284 is at 2950 with the 140 EH and 2225. The 143 elxd had a good node at 3000 with RL 23 but the case head expansion on the Lapua brass was a little more than...

   Liked On: 05-12-2018, 10:40 AM

7. 
   johnd liked post by sneeze On thread : Primer issues

   T3s have been the worst Iv seen. The ones with misfires had rust build up on the taper to the point that it was jamming in the bolt body creating light strikes. Id guess its a combination of the...

   Liked On: 26-11-2018, 07:21 PM

8. 
   Tommy liked post by sneeze On thread : Primer issues

   Pull the pin out and have a look. Its not difficult. Youl find some good how too guides on you tube. 9 times out of 10 all it needs is a good clean up and its good to go. You will know when you see...

   Liked On: 24-11-2018, 04:02 PM

9. 
   mikee liked post by sneeze On thread : introduction

   Nice web site and some sharp pricing given the low NZ dollar.

   Liked On: 24-11-2018, 03:06 PM

10. 
    Maca49 liked post by sneeze On thread : Primer issues

    Most common cause in a T3 would be a rusted firing pin. Id check that first.

    Liked On: 24-11-2018, 02:47 PM

11. 
    camo wsm liked post by sneeze On thread : introduction

    Nice web site and some sharp pricing given the low NZ dollar.

    Liked On: 24-11-2018, 02:44 PM

12. 
    GWH liked post by sneeze On thread : Labradar Down

    So last instalment. Iv had the unit for a couple of weeks now. Was well packaged and Dave included the replaced parts., looks like a mother board. I put some rim fire past it the day it arrived...

    Liked On: 20-11-2018, 10:43 PM

13. 
    xtightg liked post by sneeze On thread : Labradar Down

    Was intended to be an informative thread about a labradar warranty repair, but as with all forums the knitting group gossips have to have a little spotlight.

    Liked On: 20-11-2018, 09:17 PM

14. 
    R93 liked post by sneeze On thread : Labradar Down

    So last instalment. Iv had the unit for a couple of weeks now. Was well packaged and Dave included the replaced parts., looks like a mother board. I put some rim fire past it the day it arrived...

    Liked On: 20-11-2018, 09:06 PM

15. 
    muzr257 liked post by sneeze On thread : Labradar Down

    So last instalment. Iv had the unit for a couple of weeks now. Was well packaged and Dave included the replaced parts., looks like a mother board. I put some rim fire past it the day it arrived...

    Liked On: 20-11-2018, 08:53 PM

Page 53 of 149 First ... 33940414243444546474849505152535455565758596061626364656667103 ... Last

• Jump to page: