STC
Member

453 Likes

Page 22 of 31 First ... 8910111213141516171819202122232425262728293031 Last

• Jump to page:

1. 
   STC liked post by Proudkiwi On thread : Moving up in calibre - 300 Win, 300 WSM, 7mm RM or there?

   Also - 7prc for the win. I think tahr is on the money. Horsepower was used to overcome poor BC for a long time. You don’t need to do that anymore with current projectiles. Also also, rimmed...

   Liked On: 17-01-2024, 07:07 AM

2. 
   STC liked post by Moutere On thread : Garmin Xero® C1 Pro Chronograph

   Boom… Who shot my Labradar !!!!

   Liked On: 16-01-2024, 06:30 PM

3. 
   STC liked post by -BW- On thread : Gordons reloading tool

   For those not on discord; 241728 241729

   Liked On: 16-01-2024, 05:36 PM

4. 
   STC liked post by 6.5 CRD On thread : Moving up in calibre - 300 Win, 300 WSM, 7mm RM or there?

   This ^^ The likes of 300WM/300WSM/7RM can be made to work incredibly well if your handloading / doing a custom rifle, but in factory form using factory ammo, with the larger cals your dealing with...

   Liked On: 16-01-2024, 05:35 PM

5. 
   STC liked post by Rusky On thread : Fiordland Moose

   There could well be a breeding pair still alive, but they only live for 20-25 years roughly. The clock is ticking if not the case. Would I shoot one if I saw it? Nah, just let it walk on by...

   Liked On: 16-01-2024, 03:12 PM

6. 
   STC liked post by Mistral On thread : Moving up in calibre - 300 Win, 300 WSM, 7mm RM or there?

   Jeez this could go on forever! But hey I'm here now so....... 7mm PRC. Less recoil than the 30 cal variants, accurate, with good factory ammo available. The 6.5's will get you where you want...

   Liked On: 16-01-2024, 01:55 PM

7. 
   STC liked post by -BW- On thread : Gordons reloading tool

   That might be outdated, as according to the discussions on discord, there are volunteers who have been working on submissions and updates.

   Liked On: 16-01-2024, 12:32 PM

8. 
   STC liked post by jpurdon On thread : Moving up in calibre - 300 Win, 300 WSM, 7mm RM or there?

   Yea the reason for parting with the 270 is that its an older rifle that isn't quite as accurate as I want. I figure if I am buying a new rifle then it's a good time to change calibre and future proof...

   Liked On: 16-01-2024, 09:30 AM

9. 
   STC liked post by imaca On thread : 6.5x55 accuracy

   Re the hangfire, get your face away from the action and open the bolt with you hand in front of the bolt. You want your body parts as far away from the bolt and action as possible, so if it does go...

   Liked On: 15-01-2024, 09:15 AM

10. 
    STC liked post by grandpamac On thread : Why you keep old Powder Data Manuals

    Greetings, Printed manuals often get purged to allow for later developments but the data usually stays on web sites. I use the Nosler, Hodgdons and AD! ones plus loaddata.com and my banana boxes of...

    Liked On: 12-01-2024, 05:22 PM

11. 
    STC liked post by NewbieZAR On thread : 308

    if just bush hunting, buy the cheapest softpoints you can find, load a middle of the road load that shoots OK and go hunting. I dont even do load development for bush hunting ammo anymore, i just...

    Liked On: 12-01-2024, 03:07 PM

12. 
    STC liked post by Mick Hunter On thread : Borescope images

    Looks a bit like lead. Either way could do with a clean and recheck

    Liked On: 11-01-2024, 07:25 PM

13. 
    STC liked post by Micky Duck On thread : Chaz Forsyth in ODT.

    great to see Chaz is still around and fighting the good fight. a real gentleman and great fella to sit and yak with.

    Liked On: 11-01-2024, 12:29 PM

14. 
    STC liked post by Makros On thread : Chaz Forsyth in ODT.

    https://www.odt.co.nz/opinion/firearm-registration-laws-not-hitting-system%E2%80%99s-intended-targets

    Liked On: 11-01-2024, 11:47 AM

15. 
    STC liked post by Finnwolf On thread : Chaz Forsyth in ODT.

    Good article by Chaz in today’s Otago Daily Times. I just wish law makers would read it and take notice.

    Liked On: 11-01-2024, 11:21 AM

Page 22 of 31 First ... 8910111213141516171819202122232425262728293031 Last

• Jump to page: