Tentman
Member

4084 Likes

Page 145 of 273 First ... 4595131132133134135136137138139140141142143144145146147148149150151152153154155156157158159195245 ... Last

• Jump to page:

1. 
   grandpamac liked post by Tentman On thread : Projectiles for a .223 with a 12 inch twist.

   If your Tikka is 1:8 then I'd run it . . . Either ballast up the current stock (or a replacement plastic one ) or run it in a chassis. A heck of a lot cheaper than a revarrel and Ive never seen a...

   Liked On: 26-10-2022, 03:11 PM

2. 
   Scouser liked post by Tentman On thread : Tuatahi axe project - small axe / hatchet for hunting, tramping, fishing etc

   168031 What a great thread. Here is a little Axe I was given in memory of a friend who passed in 1998. "Clarky" (Russell Clark) was a superb Horseman, Hunter, Bushman and Craftsman (of Saddles,...

   Liked On: 22-10-2022, 01:10 PM

3. 
   gilly liked post by Tentman On thread : Re-Barreling a 96 7x57 Mauser

   You could probably get a Lothar -Walther pre contoured short chambered barrel for that action and take it back to "original".

   Liked On: 21-10-2022, 10:17 AM

4. 
   Jaco Goosen liked post by Tentman On thread : Re-Barreling a 96 7x57 Mauser

   You could probably get a Lothar -Walther pre contoured short chambered barrel for that action and take it back to "original".

   Liked On: 21-10-2022, 10:16 AM

5. 
   Jaco Goosen liked post by Tentman On thread : My new 6 mm ARC

   Nice. These wee guys (Grendel, 6.8 SPC etc) are the way of the future. Im really pleased with my CZ 527 in 6.8SPC, its my favourite hunting rifle!

   Liked On: 18-10-2022, 06:18 AM

6. 
   Bol Tackshin liked post by Tentman On thread : My new 6 mm ARC

   Nice. These wee guys (Grendel, 6.8 SPC etc) are the way of the future. Im really pleased with my CZ 527 in 6.8SPC, its my favourite hunting rifle!

   Liked On: 17-10-2022, 10:46 PM

7. 
   WireWorking liked post by Tentman On thread : My new 6 mm ARC

   Nice. These wee guys (Grendel, 6.8 SPC etc) are the way of the future. Im really pleased with my CZ 527 in 6.8SPC, its my favourite hunting rifle!

   Liked On: 17-10-2022, 09:11 PM

8. 
   Moa Hunter liked post by Tentman On thread : Marlin Ballard restoration

   how about slotting the hammer so a full diameter (but less than full width) bush can be inserted??

   Liked On: 17-10-2022, 12:39 PM

9. 
   nor-west liked post by Tentman On thread : DELTA Demo scopes

   Gidday. Could I please speak for the 4-24×50 Titanium. Thanks

   Liked On: 11-10-2022, 11:05 PM

10. 
    Joe_90 liked post by Tentman On thread : DELTA Demo scopes

    Gidday. Could I please speak for the 4-24×50 Titanium. Thanks

    Liked On: 11-10-2022, 10:53 PM

11. 
    dannyb liked post by Tentman On thread : DELTA Demo scopes

    Gidday. Could I please speak for the 4-24×50 Titanium. Thanks

    Liked On: 11-10-2022, 08:29 PM

12. 
    janleroux liked post by Tentman On thread : BSA Martini MK2

    Nice! Did you make the cheekpiece and LOP hardware yourself?, it looks really good too.

    Liked On: 09-10-2022, 06:01 PM

13. 
    Magnetite liked post by Tentman On thread : Wind reading accuracy while hunting

    ^^ The above comments about wind are a perfect example of why misses occur. You cannot see wind, only indicators of it. Wind is 3 dimensional, just ask any experienced sailor. Its like a big...

    Liked On: 08-10-2022, 09:21 PM

14. 
    Micky Duck liked post by Tentman On thread : 30mm, 30 mil (100moa) min 4x scopes

    Well bugger me, an option straight away, the Delta 4-24 ×50 fits the bill exactly. Homework now required

    Liked On: 08-10-2022, 08:17 PM

15. 
    CATLINS HUNTER liked post by Tentman On thread : Wind reading accuracy while hunting

    I'd say if you're worried about wind you are too far away away and should get closer - its called "stalking" and its a very underated skill that is way easier to learn than making wind calls!

    Liked On: 02-10-2022, 07:03 PM

Page 145 of 273 First ... 4595131132133134135136137138139140141142143144145146147148149150151152153154155156157158159195245 ... Last

• Jump to page: