Tentman
Member

3023 Likes

Page 6 of 202 First 123456789101112131415161718192056106 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Tentman On thread : Magazine help needed - misfeeding

   I haven't pulled a 581 mag down but the bolt gun ones are notorious for having the springs and followers the "wrong way round" and the first thing to try with them is reverse the spring, then the...

   Liked On: 05-05-2024, 08:49 PM

2. 
   wekaman liked post by Tentman On thread : Magazine help needed - misfeeding

   I haven't pulled a 581 mag down but the bolt gun ones are notorious for having the springs and followers the "wrong way round" and the first thing to try with them is reverse the spring, then the...

   Liked On: 05-05-2024, 10:08 AM

3. 
   Barry the hunter liked post by Tentman On thread : Any Remington 40x about?

   If you were prepared to compromise a bit there are a few of the Bergara "700 clone" 22s about, can't recall the model number

   Liked On: 03-05-2024, 09:02 PM

4. 
   RacksandRods liked post by Tentman On thread : Any Remington 40x about?

   I've been interested in the "higher end" Remmy 22s for at least 20 years and I've not seen a 40x based 22 for sale in NZ. The 541s come up occasionally but that's about it as far as I can tell . . ....

   Liked On: 03-05-2024, 07:57 PM

5. 
   Micky Duck liked post by Tentman On thread : NZDA worth joining.

   Hey POST OF THE YEAR! (me too)

   Liked On: 01-05-2024, 04:27 PM

6. 
   Mathias liked post by Tentman On thread : NZDA worth joining.

   Hey POST OF THE YEAR! (me too)

   Liked On: 01-05-2024, 04:14 PM

7. 
   Kiwi Greg liked post by Tentman On thread : NZDA worth joining.

   Hey POST OF THE YEAR! (me too)

   Liked On: 01-05-2024, 12:33 PM

8. 
   Tahr liked post by Tentman On thread : NZDA worth joining.

   Hey POST OF THE YEAR! (me too)

   Liked On: 01-05-2024, 11:51 AM

9. 
   H.M liked post by Tentman On thread : Big up’s for the Ruger American

   Supposedly there is a machined cooking piece avaliable for them in the US to replace the investment cast factory one. One of its claimed benefits is significantly reduced cocking effort, if the...

   Liked On: 29-04-2024, 05:03 PM

10. 
    caberslash liked post by Tentman On thread : Pierced ginex primers

    It might also pay to have your firing pin protrusion, diameter and fit to the firing pin hole checked. I havent heard of Howa's having issues with this atea but any manufactured item can have...

    Liked On: 28-04-2024, 09:16 AM

11. 
    BSA270 liked post by Tentman On thread : 257R Experiences

    I ran one for a number of years, it was a very nice "classic" setup built by Allan Carr on a VZ33 action with a gorgeous Slee walnut stock in his "Rigby" pattern, pre suppressor days but I didn't...

    Liked On: 21-04-2024, 06:06 PM

12. 
    Micky Duck liked post by Tentman On thread : Best/simplest alternative to a ladder chart?

    I decided to pursue this a bit and was able to get a spare hour plus to throw some new loads and get to the range. So the cheapie Hornadys with a fairly "loose" weight tolerance were identified...

    Liked On: 20-04-2024, 02:25 PM

13. 
    Rated M for Magnum liked post by Tentman On thread : Best/simplest alternative to a ladder chart?

    Now MD that's very uncharitable to take my shooting to task. I'd already covered this and previously shot two 5 shotters with my K Hornet of 0.6 and 0.4 - with the same target and a 7x scope. It...

    Liked On: 19-04-2024, 02:39 PM

14. 
    Micky Duck liked post by Tentman On thread : Best/simplest alternative to a ladder chart?

    Hey just banter both ways . . . .

    Liked On: 19-04-2024, 09:04 AM

15. 
    Puffin liked post by Tentman On thread : Best/simplest alternative to a ladder chart?

    Thanks Puffin for your most excellent posts on this subject, especially in the linked threads. To your thoughts I would add that many shooters (me included haha) are seeking groups to stoke their...

    Liked On: 18-04-2024, 10:46 PM

Page 6 of 202 First 123456789101112131415161718192056106 ... Last

• Jump to page: