Tertle
Member

238 Likes

Page 4 of 16 First 12345678910111213141516 Last

• Jump to page:

1. 
   Tertle liked post by Micky Duck On thread : 25cal hp casting oops

   they look like fun alright....wallaby medicine

   Liked On: 16-08-2021, 10:30 PM

2. 
   Tertle liked post by novembersierra On thread : Bullet prices driving me to cast..

   It's great to see that there's plenty interest in cast boolit shooting here. My first centrefire rifle was a Winchester 94 and rolling my own was just a natural move. Though my collection of calibres...

   Liked On: 29-07-2021, 11:40 PM

3. 
   Tertle liked post by marky123 On thread : Bullets

   I don't have time for this,I'm off down the range. With my pistol guns...

   Liked On: 27-07-2021, 06:46 PM

4. 
   Tertle liked post by marky123 On thread : Bullets

   No we don't.

   Liked On: 27-07-2021, 04:29 PM

5. 
   Tertle liked post by Jhon On thread : Bullet prices driving me to cast..

   Well I already shoot cast that I buy from a couple of NZ suppliers, one who seems to be absent from the market the last year or so. I started with Pistol in 45ACP and 38/357mag, and now also use cast...

   Liked On: 27-07-2021, 04:27 PM

6. 
   Tertle liked post by omark On thread : Alternative to gas checks

   .314 &.316 works well in mine with the 202gn noe molds and 4227/2205 powder charge Also the standard unique charge is also accurate Neither are gas checked

   Liked On: 26-07-2021, 12:11 AM

7. 
   Tertle liked post by novembersierra On thread : Alternative to gas checks

   Only just stumbled on this thread so apologies for the late response. I'm churning out 30 cal gas checks using a Checkmaker from Patmarlins and 0.015" aluminium coil from Yonky. Here are some...

   Liked On: 26-07-2021, 12:10 AM

8. 
   Tertle liked post by Tedz50 On thread : Spray painting boolits

   Just thinking about above post I originally used this to treat aluminum bullet molds as it is a mould release agent,also when using plastic wads always put paper side down against powder so plastic...

   Liked On: 25-07-2021, 07:20 AM

9. 
   Tertle liked post by NZ32 On thread : Powder coating trays

   Trial and error, plus a bit of youtube. Heat them a bit before adding powder, just not too much as it gets too sticky.

   Liked On: 24-07-2021, 11:18 PM

10. 
    Tertle liked post by NZ32 On thread : Powder coating trays

    Achievement for the day, not the most uniform coating but good enough for close pistol targets. 173402

    Liked On: 24-07-2021, 10:38 PM

11. 
    Tertle liked post by Driverman On thread : Powder coating trays

    I dont use the plastic pellets but just shakenbake the boolits on their own, The airsoft balls are really there to stop the powder being knocked around by the other boolits .I find that I can use...

    Liked On: 24-07-2021, 10:37 PM

12. 
    Tertle liked post by Driverman On thread : Powder coating trays

    we'll have everyone casting and powder coating before to long

    Liked On: 24-07-2021, 10:35 PM

13. 
    Tertle liked post by Driverman On thread : Powder coating trays

    Youll be a long time using up your powder. The purple I have I got from the States about 2016 and have cast over 5000 9mm etc and still have heaps left.

    Liked On: 24-07-2021, 02:59 PM

14. 
    Tertle liked post by NZ32 On thread : Powder coating trays

    Cheers guys, got some of that Eastwood stuff last week but wondered if there was a cheaper supplier around. Going to do some .358 casting this morning. The Mrs wants purple bullets for CAS so that's...

    Liked On: 24-07-2021, 02:59 PM

15. 
    Tertle liked post by ebf On thread : Stainless Media

    rambo-6mmrem before you splash out on pins, have a go with just washing cases. I use a teaspoon of citric acid powder, 1 teaspoon of the purple Palmolive dish soap in the 7lt Frankford wet...

    Liked On: 23-07-2021, 01:08 AM

Page 4 of 16 First 12345678910111213141516 Last

• Jump to page: