Tikka7mm08
Member

1711 Likes

Page 12 of 115 First 123456789101112131415161718192021222324252662112 ... Last

• Jump to page:

1. 
   veitnamcam liked post by Tikka7mm08 On thread : Trying something, Eric Cortina method of load development

   I'd say job done with those 140gn ABs now go hunting. Some on here could have a chuckle at my comment.

   Liked On: 03-09-2022, 06:22 PM

2. 
   RugerM77 liked post by Tikka7mm08 On thread : Nosler Accubond Vs Ballistic Tip terminal performance

   I found 140gn ABs and BTs shot same POI in 7mm08 model 7. Both accurate. The ABs were fantastic on big pigs but both were never found wanting really.

   Liked On: 03-09-2022, 05:55 PM

3. 
   dannyb liked post by Tikka7mm08 On thread : Trying something, Eric Cortina method of load development

   I'd say job done with those 140gn ABs now go hunting. Some on here could have a chuckle at my comment.

   Liked On: 03-09-2022, 11:59 AM

4. 
   Micky Duck liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

   A lot better but still can be seen. Going to fire new cases and size with Lee neck collet sizer. Once fired case on left. ...

   Liked On: 30-08-2022, 08:12 PM

5. 
   dannyb liked post by Tikka7mm08 On thread : Norma vs Lapua Brass: Pressure

   Hopefully the Norma will last a bit longer now load sorted. Lapua in reserve. I'll just shoot same load in Lapua and see...not expecting too much variation as reading up Lapua will out perform Norma...

   Liked On: 22-08-2022, 10:47 AM

6. 
   dannyb liked post by Tikka7mm08 On thread : Norma vs Lapua Brass: Pressure

   dannyb because I bought used Norma brass to begin with and then could only find Lapua brass.

   Liked On: 22-08-2022, 09:40 AM

7. 
   veitnamcam liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   Interesting 9 shots. 2.935" COL seems good. ...

   Liked On: 21-08-2022, 09:55 PM

8. 
   Khaos liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

   Only ever FL size...but is either die or chamber...easy to find out later this week.

   Liked On: 21-08-2022, 05:47 PM

9. 
   7mm Rem Mag liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   Very happy. Primers all good if not better than at 57.0gn and grouping all together really well despite freezing office worker hands. Good south-westerly and about 6-7deg. ...

   Liked On: 21-08-2022, 08:25 AM

10. 
    Moa Hunter liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

    Interesting 9 shots. 2.935" COL seems good. ...

    Liked On: 20-08-2022, 08:30 PM

11. 
    CBH Australia liked post by Tikka7mm08 On thread : The model 7 in your life

    Love my Stug stock model 7 in 7mm08. Has Z6i 2-12 scope, lightweight everything - bolt, pin, mounts, suppressor and shoots 120gn into 0.5MOA. ...

    Liked On: 20-08-2022, 01:32 AM

12. 
    veitnamcam liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

    Just fired factory case. It is the rifle. ...

    Liked On: 19-08-2022, 10:01 PM

13. 
    Micky Duck liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

    Action closed...albeit stiffly...on the no go gauge but not on the field no go. So safe to shoot but at the edge... going to run reamer in chamber to see if burr comes off.

    Liked On: 19-08-2022, 06:58 PM

14. 
    Micky Duck liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

    Just fired factory case. It is the rifle. ...

    Liked On: 18-08-2022, 08:27 PM

15. 
    dannyb liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

    Dropped of to the gunsmith for a good polish...thinks swarf may have got caught when barrel was cut (or something like that) and happened at production. Is contacting agent.

    Liked On: 18-08-2022, 07:43 PM

Page 12 of 115 First 123456789101112131415161718192021222324252662112 ... Last

• Jump to page: