Tikka7mm08
Member

1711 Likes

Page 24 of 115 First ... 101112131415161718192021222324252627282930313233343536373874 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Drop table with 180gn ELDM @ 2850fps 100y zero. Note BC used is 0.796. This BC is from the hornady website. I'll be able to try real world test on 600y gong at home. Absolute hammer. ...

   Liked On: 31-01-2022, 07:24 PM

2. 
   SPEARONZ liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Drop table with 180gn ELDM @ 2850fps 100y zero. Note BC used is 0.796. This BC is from the hornady website. I'll be able to try real world test on 600y gong at home. Absolute hammer. ...

   Liked On: 31-01-2022, 03:19 PM

3. 
   Nathan F liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Drop table with 180gn ELDM @ 2850fps 100y zero. Note BC used is 0.796. This BC is from the hornady website. I'll be able to try real world test on 600y gong at home. Absolute hammer. ...

   Liked On: 31-01-2022, 01:30 PM

4. 
   dannyb liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Drop table with 180gn ELDM @ 2850fps 100y zero. Note BC used is 0.796. This BC is from the hornady website. I'll be able to try real world test on 600y gong at home. Absolute hammer. ...

   Liked On: 31-01-2022, 10:28 AM

5. 
   burtonator liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Group shot this evening. 180gn ELDM with 58.6gn RE26, CCI LRM primer, Norma brass. COAL 3.380" per burtonator. ...

   Liked On: 30-01-2022, 04:20 PM

6. 
   chainsaw liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   First 3 shots. Clean cold barrel. https://uploads.tapatalk-cdn.com/20210523/4b979613209fe20a6ff7d815aecfa8d6.jpg Sent from my SM-G986B using Tapatalk

   Liked On: 30-01-2022, 01:38 PM

7. 
   chainsaw liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

   Group shot this evening. 180gn ELDM with 58.6gn RE26, CCI LRM primer, Norma brass. COAL 3.380" per burtonator. ...

   Liked On: 30-01-2022, 01:36 PM

8. 
   veitnamcam liked post by Tikka7mm08 On thread : Ecinomical load development in a component drought.

   Good approach grandpamac - lots can vary, I am comfortable adding a low tub of powder to a new one if the lot numbers are the same, but not otherwise (even though after a good shake I doubt there...

   Liked On: 29-01-2022, 04:39 PM

9. 
   Moa Hunter liked post by Tikka7mm08 On thread : Ecinomical load development in a component drought.

   Good approach grandpamac - lots can vary, I am comfortable adding a low tub of powder to a new one if the lot numbers are the same, but not otherwise (even though after a good shake I doubt there...

   Liked On: 29-01-2022, 02:37 PM

10. 
    grandpamac liked post by Tikka7mm08 On thread : Ecinomical load development in a component drought.

    Good approach grandpamac - lots can vary, I am comfortable adding a low tub of powder to a new one if the lot numbers are the same, but not otherwise (even though after a good shake I doubt there...

    Liked On: 29-01-2022, 12:20 PM

11. 
    Micky Duck liked post by Tikka7mm08 On thread : not enough elevation in scope

    That is weird. Can you swap front and back rings over to see if that solves it? Others will be along with thoughts.

    Liked On: 24-01-2022, 09:53 PM

12. 
    JohnQT liked post by Tikka7mm08 On thread : Full Length or Neck sizing. What is better and why?

    Tonight tried comp shellholders to FL size and chamber. Normal shellholder requires body die after FL die and then chambers easily. First removed firing pin and this is done by cocking the bolt...

    Liked On: 24-01-2022, 01:18 PM

13. 
    Cyclops liked post by Tikka7mm08 On thread : Full Length or Neck sizing. What is better and why?

    Tonight tried comp shellholders to FL size and chamber. Normal shellholder requires body die after FL die and then chambers easily. First removed firing pin and this is done by cocking the bolt...

    Liked On: 21-01-2022, 11:38 AM

14. 
    winaa liked post by Tikka7mm08 On thread : 120g 7mm-08 Load data?

    120gn Nosler BTs and 50gn 2209 is a load that has worked extremely well across several T3s and a Mod 7. Norma brass. I even used 140gn BT with 50gn 2209 no problem but approach that with usual...

    Liked On: 21-01-2022, 08:29 AM

15. 
    zimmer liked post by Tikka7mm08 On thread : Full Length or Neck sizing. What is better and why?

    Tonight tried comp shellholders to FL size and chamber. Normal shellholder requires body die after FL die and then chambers easily. First removed firing pin and this is done by cocking the bolt...

    Liked On: 20-01-2022, 08:11 PM

Page 24 of 115 First ... 101112131415161718192021222324252627282930313233343536373874 ... Last

• Jump to page: