Tikka7mm08
Member

1745 Likes

Page 90 of 117 First ... 40767778798081828384858687888990919293949596979899100101102103104 ... Last

• Jump to page:

1. 
   Tikka7mm08 liked post by zimmer On thread : 7mmSaum Load Ratio in Model 7

   64278

   Liked On: 22-02-2017, 12:41 PM

2. 
   Tikka7mm08 liked post by zimmer On thread : 7mmSaum Load Ratio in Model 7

   Mine's is pretty crude - a piece of straight copper pipe left over from my house build. A funnel cut as required and epoxied to the tube. The secret then is to tip the powder into the funnel and...

   Liked On: 22-02-2017, 12:41 PM

3. 
   Tikka7mm08 liked post by zimmer On thread : 7mmSaum Load Ratio in Model 7

   Have you tried a long drop tube? I have a home made drop tube about 500mm long and I can get around 1.5mm further settle (depending on powder) in a 284 sized case.

   Liked On: 21-02-2017, 09:10 PM

4. 
   Tikka7mm08 liked post by GWH On thread : 7mmSaum Load Ratio in Model 7

   I don't believe there is an equivalent, it's too new for my ver of QL Sent from my SM-G900I using Tapatalk

   Liked On: 21-02-2017, 08:48 PM

5. 
   Tikka7mm08 liked post by nevereadyfreddy On thread : 7mmSaum Load Ratio in Model 7

   Had good results with 2209, 56gr was best in my rifle. Am now using RL19. 59 gr. Is compressed a bit. Both with 160 NABs

   Liked On: 21-02-2017, 08:13 PM

6. 
   Tikka7mm08 liked post by R93 On thread : My 260AI Load Development Begins

   I just used an .30 cal collar on an OAL gauge to measure the bump. I don't bother any more. But yeah, just adjust the die down an 1/8 of a turn until you achieve the desired result. All that you...

   Liked On: 20-02-2017, 01:52 PM

7. 
   Tikka7mm08 liked post by zimmer On thread : My 260AI Load Development Begins

   If you don't have a gauge - I have a Sinclair 40 degree one - the best way is to remove the striker/firing pin assembly from your bolt and with the bare remainder chamber your cases. This way you can...

   Liked On: 20-02-2017, 01:52 PM

8. 
   Tikka7mm08 liked post by johnd On thread : My 260AI Load Development Begins

   Might be time to invest in a comparator of some sort, or if you are handy with a lathe make something up to fit on your caliper blade. They are a handy way of knowing / measuring what your moving...

   Liked On: 20-02-2017, 01:46 PM

9. 
   Tikka7mm08 liked post by Mathias On thread : My 260AI Load Development Begins

   Wow, they are coming out great now. You should be stoked :thumbsup: Sure saves a bit of stuffing around with shotgun powder etc.

   Liked On: 18-02-2017, 01:46 PM

10. 
    Tikka7mm08 liked post by buzzman On thread : My 260AI Load Development Begins

    2900 in my standard 260 with the 143 eld-x and superformance

    Liked On: 17-02-2017, 07:07 PM

11. 
    Tikka7mm08 liked post by R93 On thread : My 260AI Load Development Begins

    Being the mong I am, I would have completely sussed it by looking at it and then proceeded to destroy 30 cases before I bothered reading the instructions. 😆 Sent from my SM-G935F using Tapatalk

    Liked On: 16-02-2017, 07:12 PM

12. 
    Tikka7mm08 liked post by Smiddy On thread : AMP Annealing Service for Forum Members?

    Now I have to shoot all my rounds so I can send to you :)( Sent from my iPhone using Tapatalk

    Liked On: 12-02-2017, 09:35 PM

13. 
    Tikka7mm08 liked post by GWH On thread : Gun Porn, show off your new toys

    Just replaced my Viper HS-T with a Viper PST 4-16×50 FFP on my model 7 7mm SAUM. Looking forward to using the illuminated reticle at a few spots where the deer come out right on...

    Liked On: 08-02-2017, 08:08 PM

14. 
    Tikka7mm08 liked post by Mathias On thread : AMP Annealing Service for Forum Members?

    Very nice :) Cool gear to have

    Liked On: 03-02-2017, 08:01 PM

15. 
    Tikka7mm08 liked post by Dr. Watson On thread : Gun Porn, show off your new toys

    63183

    Liked On: 02-02-2017, 11:46 PM

Page 90 of 117 First ... 40767778798081828384858687888990919293949596979899100101102103104 ... Last

• Jump to page: