Tikka7mm08
Member

1660 Likes

Page 10 of 111 First 12345678910111213141516171819202122232460110 ... Last

• Jump to page:

1. 
   Marty Henry liked post by Tikka7mm08 On thread : Ring/groove at base of case shoulder

   Yes I anneal. Going to fire a factory case...check then vivid neck/shoulder and FL size to see what the die is doing. Will run die in sonic cleaner and give good clean. Will try later in the week and...

   Liked On: 14-08-2022, 09:06 PM

2. 
   25/08 IMP liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   Here if anyone wants them.

   Liked On: 14-08-2022, 07:14 PM

3. 
   Micky Duck liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

   Worse still there was money on it.

   Liked On: 14-08-2022, 01:25 PM

4. 
   dannyb liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

   For bipod and sinclair rest so off bags.

   Liked On: 14-08-2022, 01:24 PM

5. 
   Micky Duck liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

   Removed stock to fit rail for mtn gear bipod. First group afterwards 168gn AMax 50g RE17....

   Liked On: 14-08-2022, 01:24 PM

6. 
   dannyb liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

   Removed stock to fit rail for mtn gear bipod. First group afterwards 168gn AMax 50g RE17....

   Liked On: 14-08-2022, 01:21 PM

7. 
   DBD liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   143gn ELDX on left at 2.955" COL and same again on right at 3.015" COL (30 thou jump and fits in mag). Testing longer length at 60 and 60.5gn with RE26. ...

   Liked On: 14-08-2022, 08:48 AM

8. 
   dannyb liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   I tend to go OTT when getting into something new. No 7mm in the cabinet now except a young fella I load for every now and then...but always could be drawn back to a 7mmSaum in the future after having...

   Liked On: 13-08-2022, 09:51 PM

9. 
   veitnamcam liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

   143gn ELDX on left at 2.955" COL and same again on right at 3.015" COL (30 thou jump and fits in mag). Testing longer length at 60 and 60.5gn with RE26. ...

   Liked On: 13-08-2022, 09:50 PM

10. 
    Dreamer liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

    Tried the Kimber with a H2 A-Tec QD suppressor. Shot very well. ...

    Liked On: 04-08-2022, 08:10 PM

11. 
    T.FOYE liked post by Tikka7mm08 On thread : 6.5 PRC Load Development Begins

    Going to start with the ELDX. If accurate will return the Bergers. https://uploads.tapatalk-cdn.com/20220721/65521164416e9ab6dafbcbe44f7a4f5b.jpg Sent from my SM-G998B using Tapatalk

    Liked On: 02-08-2022, 08:14 PM

12. 
    Shearer liked post by Tikka7mm08 On thread : Tikka Veil Factory Stock Weight

    Weighed the stock tonight. Lighter than I expected... not a huge saving going to a CF replacement? ...

    Liked On: 01-08-2022, 06:33 PM

13. 
    hotsoup liked post by Tikka7mm08 On thread : Fitting Mtn Gear Bipod Picatinny Rail - Must Use Gunsmith?

    https://www.instagram.com/p/CaixJqYJf7M/ Sorted.

    Liked On: 30-07-2022, 11:20 PM

14. 
    Muttonguts liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

    Managed to bag a buck on Stewart Is. trip. The 168gn went straight through and would probably try a much lighter bullet next time. It was an unexpected 'long range' shot too at 350ish yards. ...

    Liked On: 30-07-2022, 08:53 AM

15. 
    Muttonguts liked post by Tikka7mm08 On thread : Kimber Montana 308 Load Development

    I have GREAT taste in whisky, poor taste in friends :yaeh am not durnk:

    Liked On: 30-07-2022, 08:35 AM

Page 10 of 111 First 12345678910111213141516171819202122232460110 ... Last

• Jump to page: