tommygun
Member

442 Likes

Page 2 of 30 First 12345678910111213141516 ... Last

• Jump to page:

1. 
   No.3 liked post by tommygun On thread : Flush fitting internal mag for Howa mini

   271298271299 Just a little something I've been working on. 3d printing prototypes at the moment. The mag body fits into the original mag well and is retained by the factory magazine catch pin. Also...

   Liked On: 25-03-2025, 06:16 PM

2. 
   Barefoot liked post by tommygun On thread : Flush fitting internal mag for Howa mini

   271298271299 Just a little something I've been working on. 3d printing prototypes at the moment. The mag body fits into the original mag well and is retained by the factory magazine catch pin. Also...

   Liked On: 25-03-2025, 06:01 PM

3. 
   Deanohit liked post by tommygun On thread : LEE Enfield Carbine restoration

   Finished, or as close to it as I'm going to get until a cheap, original stock set comes up for sale. (yeah right) 161952

   Liked On: 14-03-2025, 07:41 PM

4. 
   rupert liked post by tommygun On thread : Baikal - dragging firing pin issues

   163471 I couldn't attach this to the PM but you can see the cross pin here halfway out the right side.

   Liked On: 02-02-2025, 09:12 PM

5. 
   Northkiwi liked post by tommygun On thread : Bubba what have you done?

   This thread is making me want an Obrez. Pretty impractical but I suppose if there's a bear trying to break into your yurt and it didn't listen when you politely explained "cyka blyat idi na hoy" then...

   Liked On: 22-01-2025, 09:59 PM

6. 
   canross liked post by tommygun On thread : Monolithic copper hollowpoints

   Turns out that when an engineering firm has a CNC lathe and most of its staff are hunters, eventually someone starts designing solid copper bullets for their 300blk.265715

   Liked On: 06-01-2025, 08:31 PM

7. 
   BSA270 liked post by tommygun On thread : Monolithic copper hollowpoints

   Turns out that when an engineering firm has a CNC lathe and most of its staff are hunters, eventually someone starts designing solid copper bullets for their 300blk.265715

   Liked On: 01-01-2025, 09:36 PM

8. 
   bjp liked post by tommygun On thread : Monolithic copper hollowpoints

   Turns out that when an engineering firm has a CNC lathe and most of its staff are hunters, eventually someone starts designing solid copper bullets for their 300blk.265715

   Liked On: 28-12-2024, 01:08 PM

9. 
   rupert liked post by tommygun On thread : Monolithic copper hollowpoints

   265716265717265718265719265720265721 Ours pictured next to a Peregrine one, I was finding the cup of the seating die was breaking the three pre-defined petals of the bullet, so I designed a seating...

   Liked On: 28-12-2024, 12:43 PM

10. 
    Micky Duck liked post by tommygun On thread : Monolithic copper hollowpoints

    I've been loading them for the boss's 300BLK, he says they shoot well but I want to try a few in my 308. I think the copper bar he used was 10mm, so I also want to convince him to let me make some...

    Liked On: 28-12-2024, 11:17 AM

11. 
    Micky Duck liked post by tommygun On thread : Monolithic copper hollowpoints

    265716265717265718265719265720265721 Ours pictured next to a Peregrine one, I was finding the cup of the seating die was breaking the three pre-defined petals of the bullet, so I designed a seating...

    Liked On: 28-12-2024, 11:16 AM

12. 
    Micky Duck liked post by tommygun On thread : Bruce Rifle Club?

    The current secretary is not as good as the previous one and is a bit useless in general. But yes, the above poster is correct, the Bruce Rifle Club is hesitant to take on new members. Engage in some...

    Liked On: 28-12-2024, 11:07 AM

13. 
    canross liked post by tommygun On thread : Monolithic copper hollowpoints

    265716265717265718265719265720265721 Ours pictured next to a Peregrine one, I was finding the cup of the seating die was breaking the three pre-defined petals of the bullet, so I designed a seating...

    Liked On: 27-12-2024, 11:13 PM

14. 
    makka liked post by tommygun On thread : Monolithic copper hollowpoints

    265716265717265718265719265720265721 Ours pictured next to a Peregrine one, I was finding the cup of the seating die was breaking the three pre-defined petals of the bullet, so I designed a seating...

    Liked On: 27-12-2024, 07:33 PM

15. 
    makka liked post by tommygun On thread : Monolithic copper hollowpoints

    Turns out that when an engineering firm has a CNC lathe and most of its staff are hunters, eventually someone starts designing solid copper bullets for their 300blk.265715

    Liked On: 27-12-2024, 07:32 PM

Page 2 of 30 First 12345678910111213141516 ... Last

• Jump to page: