veitnamcam
Almost literate.

33630 Likes

Page 1355 of 2242 First ... 3558551255130513411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369140514551855 ... Last

• Jump to page:

1. 
   veitnamcam liked post by 7mmsaum On thread : Moving from AMAX to ELD

   They are working just as good as the Amax and have a bearing surface that's further forward, so fit better as "just touch loads" in most magazines.

   Liked On: 04-11-2016, 02:15 PM

2. 
   veitnamcam liked post by Tommy On thread : Dinner thread?

   Workshop won a smoker. Put lunch on at 7am hahaha 58392

   Liked On: 04-11-2016, 12:24 PM

3. 
   veitnamcam liked post by MSL On thread : Long range rifle rig photos

   Needed a spotter to see your hits/misses but can see feathers at 1300

   Liked On: 04-11-2016, 08:34 AM

4. 
   veitnamcam liked post by oraki On thread : Long range rifle rig photos

   58343 Surprised that this one hasn't come up yet

   Liked On: 04-11-2016, 08:34 AM

5. 
   veitnamcam liked post by FatLabrador On thread : What little pesties did you bowl over today?

   Cheeking the doc 200s. Found 3 alive kittens but hard to shoot them but I am only 14. All my friends were probably playing on there Xboxes while i was doing this

   Liked On: 04-11-2016, 06:58 AM

6. 
   veitnamcam liked post by homebrew.357 On thread : New barrel

   Hi Guys, I am / have made a new barrel for my Hawken plains rifle, the first barrel was good with a patched round ball, 2" group at 50m, but the barrel had a tight spot six inches in from the muzzle...

   Liked On: 03-11-2016, 10:43 PM

7. 
   veitnamcam liked post by homebrew.357 On thread : New barrel

   So I can make black powder muzzle loading barrels ,round or octagonal from 1" or a bit bigger diameter steel, bore .445", cut rifling makes it .457". Now as they are only for black powder 1215 or...

   Liked On: 03-11-2016, 10:42 PM

8. 
   veitnamcam liked post by Pointer On thread : Failure in the nest department...

   stick them under a broody hen! Or mail them to me I've got a few hens sitting at the moment

   Liked On: 03-11-2016, 10:37 PM

9. 
   veitnamcam liked post by EeeBees On thread : Failure in the nest department...

   58372 this hopefully will be better...:O_O: oh the joys of broadband in the rurals...

   Liked On: 03-11-2016, 10:37 PM

10. 
    veitnamcam liked post by Ryan On thread : Failure in the nest department...

    EeeBees the photo you've uploaded is bung - try uploading it again?

    Liked On: 03-11-2016, 10:37 PM

11. 
    veitnamcam liked post by Pengy On thread : Going over to the dark side

    I received a package from our own legend that is Gadgetman today. What can I say ? The good buggers on here are simply amazing :thumbsup: Had a bit of an issue with the scales refusing to zero,...

    Liked On: 03-11-2016, 09:40 PM

12. 
    veitnamcam liked post by GWH On thread : DIY steel 'gong' target

    Ok got ya. That pretty much explains it I reckon. Mild steel and a solid or steel core bullet, hence potential for ricochets. If you are shooting standard copper/lead hunting/target type...

    Liked On: 03-11-2016, 07:59 PM

13. 
    veitnamcam liked post by R93 On thread : DIY steel 'gong' target

    Most of the tracer ricochet is the cup coming off the base. Not the whole projectile. All my plates are angled but from poor design rather than intentions 😆 I have seen a projectile come back to...

    Liked On: 03-11-2016, 07:58 PM

14. 
    veitnamcam liked post by GWH On thread : DIY steel 'gong' target

    Quite simply, I can see the evidence of the bullet splash on the gong Sent from my SM-G900I using Tapatalk

    Liked On: 03-11-2016, 07:58 PM

15. 
    veitnamcam liked post by GWH On thread : DIY steel 'gong' target

    In my experience there's no need to angle them down when shooting at long range as the bullet is basically falling from the sky on that angle anyway. Just hAve them hung from top and able to swing...

    Liked On: 03-11-2016, 07:56 PM

Page 1355 of 2242 First ... 3558551255130513411342134313441345134613471348134913501351135213531354135513561357135813591360136113621363136413651366136713681369140514551855 ... Last

• Jump to page: