veitnamcam
Almost literate.

33625 Likes

Page 4 of 2242 First 123456789101112131415161718541045041004 ... Last

• Jump to page:

1. 
   veitnamcam liked post by Tahr On thread : Maker Mucking About

   176 yards. 62 grn (.223). 270236 Entrence 270239 Bullet was just sitting under here 270237

   Liked On: 30-04-2025, 04:47 PM

2. 
   veitnamcam liked post by Tahr On thread : Maker Mucking About

   The insides of this deer: Under the shoulder (entry). 266148 Inside, entry. 266149 Exit 266150

   Liked On: 30-04-2025, 04:44 PM

3. 
   veitnamcam liked post by Tahr On thread : Maker Mucking About

   I would say so looking at that heart. And here's a doe's lung from last evening too. Quartering towards me. 145 yards. Bullet punched out through the paunch. 265912 265911 265913

   Liked On: 30-04-2025, 04:43 PM

4. 
   veitnamcam liked post by Shearer On thread : Maker Mucking About

   I butchered the pig this morning and this is what I found of the projectile. Two petals and the base weighing 79 grains (of 110). Any other bits may have been in the discarded guts. 274114...

   Liked On: 30-04-2025, 04:42 PM

5. 
   veitnamcam liked post by PillowDribbler On thread : Camping Pod

   This was in my F/B feed,pretty cool idea.Looked at doing this with a water tank years ago.https://www.tuffrotomoulders.co.nz/page/80490-bushline-camping-canopies.

   Liked On: 30-04-2025, 04:38 PM

6. 
   veitnamcam liked post by Kiwi Greg On thread : 22 Grendel, slightly bigger brother to the 22 ARC

   I built this in late 2022 with a Howa mini & factory 223 1-8 19" barrel, been sitting in the safe for a couple of years since then, I had an AR upper in 22 Grendel back in the good old days ...

   Liked On: 30-04-2025, 09:51 AM

7. 
   veitnamcam liked post by Dan88 On thread : 22 Grendel, slightly bigger brother to the 22 ARC

   Afficionado I believe is the correct name

   Liked On: 30-04-2025, 09:50 AM

8. 
   veitnamcam liked post by 199p On thread : 22 Grendel, slightly bigger brother to the 22 ARC

   .223 22 arc 22 grendle 22x47lap 22cm 22-243ai your addicted for sure haha

   Liked On: 30-04-2025, 09:50 AM

9. 
   veitnamcam liked post by csmiffy On thread : Knife sharpening angles

   Well at the local freezing works they have a not only a sharpening robot but also a small bench mount. Bothe set up at the same angle. 18 degrees I think. It's the optimum for edge and general...

   Liked On: 30-04-2025, 09:43 AM

10. 
    veitnamcam liked post by Nick-D On thread : Knife sharpening angles

    Pig hair is farking hard on blades, combine that with a shit pull through and i don't think you have much hope in keeping the knife sharp for long. Get him a simple strop, harder to fuck the edge...

    Liked On: 30-04-2025, 09:42 AM

11. 
    veitnamcam liked post by Southcity On thread : Moose

    I shot this Fallow buck in Canada. 274081

    Liked On: 30-04-2025, 09:40 AM

12. 
    veitnamcam liked post by Ryan_Songhurst On thread : Gun Porn, show off your new toys

    You're onto it.... For some reason when I took the 1" talleys off to put the 30mm ones on the very front screw just snapped off while I was undoing it. Thought I would drill it out so set it up in...

    Liked On: 30-04-2025, 09:33 AM

13. 
    veitnamcam liked post by Ryan_Songhurst On thread : Gun Porn, show off your new toys

    Let's just say my gunsmithing career never really took off..

    Liked On: 30-04-2025, 09:32 AM

14. 
    veitnamcam liked post by Shearer On thread : Maker Mucking About

    Not .22 cal but 30cal Maker TRex. I ordered some 110gn TRex standard velocity projectiles but was mistakenly sent the 110gn 300BLK version. Although Maker didn't get back to me when I asked what...

    Liked On: 29-04-2025, 09:14 PM

15. 
    veitnamcam liked post by zeropak On thread : EX Demo Commercial vacuum sealer

    I have a STATUS ProVac ex demo machine which is excess to requirements. Here is a link to the specs. https://zeropak.co.nz/status-provac-professional-vacuum-sealer/ Perfect working order, it will...

    Liked On: 29-04-2025, 04:09 PM

Page 4 of 2242 First 123456789101112131415161718541045041004 ... Last

• Jump to page: