Walker
Member

219 Likes

Page 10 of 15 First 123456789101112131415 Last

• Jump to page:

1. 
   bumblefoot liked post by Walker On thread : Scope mounts for 223 (also sighting in & scope advice.....)

   2" high is pretty much the go, warne rings are very good but somewhat expensive, the burris or leupold steels take a lot of beating.

   Liked On: 14-07-2018, 10:01 PM

2. 
   dannyb liked post by Walker On thread : Scope mounts for 223 (also sighting in & scope advice.....)

   2" high is pretty much the go, warne rings are very good but somewhat expensive, the burris or leupold steels take a lot of beating.

   Liked On: 14-07-2018, 09:57 PM

3. 
   csmiffy liked post by Walker On thread : P17 barrel

   The coned breech assists in chambering of the 30-06 cartridge, helps it into the chamber with fast cycling. The 303 didn't require it as its much more tapered and the mag lines the projectile...

   Liked On: 09-07-2018, 06:31 PM

4. 
   lau lau liked post by Walker On thread : 350 Remington magnum

   86118

   Liked On: 29-06-2018, 07:00 PM

5. 
   Micky Duck liked post by Walker On thread : Opinion on the 7mm WSM please

   A 7-08 will do anything under 200m the WSM will do with alot less recoil and noise and I think you can get a short track in 7-08

   Liked On: 25-06-2018, 10:55 PM

6. 
   rewa liked post by Walker On thread : powder reduction when changing brass?

   Another trick is fill both types of cases with water to the top then weigh the water, reduce your load the percentage of weight difference and it will be pretty close to = velocity/pressure.

   Liked On: 03-06-2018, 08:47 PM

7. 
   PERRISCICABA liked post by Walker On thread : powder reduction when changing brass?

   Another trick is fill both types of cases with water to the top then weigh the water, reduce your load the percentage of weight difference and it will be pretty close to = velocity/pressure.

   Liked On: 02-06-2018, 09:24 AM

8. 
   Fireflite liked post by Walker On thread : Rule of Thumb!?

   Stress in a barrel will cause it to move with heat, but this only occurs if a barrel hasn't been de-stressed after machining. A quick check is to hold the action and tap the barrel with a piece of...

   Liked On: 27-05-2018, 11:02 PM

9. 
   muzr257 liked post by Walker On thread : Custom build ideas

   I've been down this road a number of times in the past and the only advice I can offer is use a standard off the shelf caliber that you can get in any town like 7mm rem mag, use a good standard...

   Liked On: 26-05-2018, 11:13 AM

10. 
    csmiffy liked post by Walker On thread : First rifle

    Alot depends on how the barrel has been made and the care with how the chamber was cut or barrel and chamber forged in one process. "Roughly" cut chambers can have microscopic radial grooves left in...

    Liked On: 11-05-2018, 07:37 PM

11. 
    Bigash liked post by Walker On thread : First rifle

    Opinions are like assholes, everyone has one! Having actually hunted around the Rotorua area, a 243 with 100grn sp's will do just about everything barring big sambar. Light recoil with supressor,...

    Liked On: 06-05-2018, 03:50 PM

12. 
    northdude liked post by Walker On thread : First rifle

    Opinions are like assholes, everyone has one! Having actually hunted around the Rotorua area, a 243 with 100grn sp's will do just about everything barring big sambar. Light recoil with supressor,...

    Liked On: 05-05-2018, 07:36 PM

13. 
    blake liked post by Walker On thread : First rifle

    If you want a inexpensive accurate rifle consider a savage. They will genraly shoot all factory ammo inside 3/4 inch and don't need wrapping in cotten wool like the Euro trash:D

    Liked On: 05-05-2018, 04:18 PM

14. 
    Savage1 liked post by Walker On thread : First rifle

    If you want a inexpensive accurate rifle consider a savage. They will genraly shoot all factory ammo inside 3/4 inch and don't need wrapping in cotten wool like the Euro trash:D

    Liked On: 05-05-2018, 02:54 PM

15. 
    berg243 liked post by Walker On thread : First rifle

    Opinions are like assholes, everyone has one! Having actually hunted around the Rotorua area, a 243 with 100grn sp's will do just about everything barring big sambar. Light recoil with supressor,...

    Liked On: 05-05-2018, 01:45 PM

Page 10 of 15 First 123456789101112131415 Last

• Jump to page: