zimmer
Member

2610 Likes

Page 69 of 174 First ... 195556575859606162636465666768697071727374757677787980818283119169 ... Last

• Jump to page:

1. 
   johnd liked post by zimmer On thread : Playing with some Redding Competition Shell Holders

   I bought two 50s and one 100 of the new type of Delta Mike. The new proper clips are superb. Likewise the hinges. My Fullbore and later F Class mound ammo box is an old MTM 100. I can get enough...

   Liked On: 14-11-2021, 05:39 PM

2. 
   RugerM77 liked post by zimmer On thread : Playing with some Redding Competition Shell Holders

   Here's a chart to help understand Redding Competition Shell Holders and what effect they have. This is my set measured using a Mitutoyo depth micrometer so reasonably accurate. I measured at three...

   Liked On: 14-11-2021, 03:51 PM

3. 
   Moa Hunter liked post by zimmer On thread : Trying something, Eric Cortina method of load development

   I have used all sorts of methods - split case necks and close on long seated bullet, Stoney Point (now Hornady OAL gauge) method, Sinclairs tool for measuring seating depth (lies in cupboard unused),...

   Liked On: 14-11-2021, 11:29 AM

4. 
   RugerM77 liked post by zimmer On thread : Trying something, Eric Cortina method of load development

   I have used all sorts of methods - split case necks and close on long seated bullet, Stoney Point (now Hornady OAL gauge) method, Sinclairs tool for measuring seating depth (lies in cupboard unused),...

   Liked On: 13-11-2021, 06:50 PM

5. 
   Puffin liked post by zimmer On thread : Trying something, Eric Cortina method of load development

   I have used all sorts of methods - split case necks and close on long seated bullet, Stoney Point (now Hornady OAL gauge) method, Sinclairs tool for measuring seating depth (lies in cupboard unused),...

   Liked On: 13-11-2021, 06:30 PM

6. 
   dannyb liked post by zimmer On thread : Trying something, Eric Cortina method of load development

   I have used all sorts of methods - split case necks and close on long seated bullet, Stoney Point (now Hornady OAL gauge) method, Sinclairs tool for measuring seating depth (lies in cupboard unused),...

   Liked On: 13-11-2021, 05:47 PM

7. 
   Moa Hunter liked post by zimmer On thread : Urgent Advice - Would you buy this 4WD?

   Mate, when I was an apprentice and given the task to apply the Denso there was noting namby-pamby around like Nitrile gloves. "Harden up boy". Likewise we got exposed to transformer oil (PCB) and...

   Liked On: 13-11-2021, 12:46 PM

8. 
   bunji liked post by zimmer On thread : A hunt for Capt'n Ron

   My regular fallow spot had a white hind that I saw on several occasions over a couple of seasons. The farmer banned me from shooting it which was perfectly OK with me. Even if I'd seen it prior to...

   Liked On: 11-11-2021, 06:45 PM

9. 
   BSA270 liked post by zimmer On thread : .222 turning back the clock

   I had a BSA Monarch (terrible full length action) and then an Anschutz 222. Through straight out inexperience I never got the best out of my 222s so sold and replaced with a 22-250. Already had a...

   Liked On: 10-11-2021, 10:11 PM

10. 
    Russian 22. liked post by zimmer On thread : Farmer lying about paper road?

    I looked at this about a year ago. Wasn't for hunting access though, was for other reasons. Read this https://www.walkingaccess.govt.nz/knowledge/access/unformed-legal-roads/ It's a matter of...

    Liked On: 10-11-2021, 09:40 PM

11. 
    Hahn liked post by zimmer On thread : Farmer lying about paper road?

    I looked at this about a year ago. Wasn't for hunting access though, was for other reasons. Read this https://www.walkingaccess.govt.nz/knowledge/access/unformed-legal-roads/ It's a matter of...

    Liked On: 10-11-2021, 05:56 PM

12. 
    bigbear liked post by zimmer On thread : Farmer lying about paper road?

    I looked at this about a year ago. Wasn't for hunting access though, was for other reasons. Read this https://www.walkingaccess.govt.nz/knowledge/access/unformed-legal-roads/ It's a matter of...

    Liked On: 10-11-2021, 05:55 PM

13. 
    Cordite liked post by zimmer On thread : Screwdriver advice

    Like this 182779

    Liked On: 07-11-2021, 12:54 PM

14. 
    Beaker liked post by zimmer On thread : Screwdriver advice

    Wiha (made in Germany) will not have JIS markings but correct for Japanese made.

    Liked On: 04-11-2021, 07:58 PM

15. 
    Hutch liked post by zimmer On thread : Screwdriver advice

    Yeah, you've got to watch the electrical "wholesalers". I even shop around for electrical fittings b4 I buy stuff on my Cory's account. $106 is still dear for a very small selection of...

    Liked On: 04-11-2021, 05:06 PM

Page 69 of 174 First ... 195556575859606162636465666768697071727374757677787980818283119169 ... Last

• Jump to page: