zimmer
Member

1490 Likes

Page 18 of 100 First ... 456789101112131415161718192021222324252627282930313268 ... Last

• Jump to page:

1. 
   zimmer liked post by flock On thread : Die TRedding locking rings.

   Tip Redding although being top of the line dies, provide a barbaric locking ring system, that will damage the thread of your dies. Solution insert a fine piece of shotgun shot into the thread then...

   Liked On: 18-08-2023, 04:58 PM

2. 
   zimmer liked post by 30.06king On thread : Die TRedding locking rings.

   Fully agree. Redding - fantastic dies, crap locking ring system. I've replaced all Redding locking rings with the much more useful Hornady Die Locking Rings that don't have any mechanism contact with...

   Liked On: 18-08-2023, 04:49 PM

3. 
   zimmer liked post by Trav-6mmrem On thread : Pros & Cons - Maxtoch vs Olight Javelot (Spotlight)

   Had a bloody good run out of my olight for the last 4 years, seen deer past 1k, runs all night. Would be absolutely perfect if it had abit wider beam but other than that I can't complain

   Liked On: 15-08-2023, 05:34 PM

4. 
   zimmer liked post by Puddleduk On thread : I'm an idiot.

   I ticked the wrong box I promise

   Liked On: 15-08-2023, 10:08 AM

5. 
   zimmer liked post by Micky Duck On thread : I'm an idiot.

   now where the heck did I put that list?????

   Liked On: 14-08-2023, 05:59 PM

6. 
   zimmer liked post by Puffin On thread : 284 seating depth query

   Don't forget this bit. Without any further instruction it's odd-on that Gunworks would cut the freebore to have your dummy rounds just touching the rifling. If you then decide to experiment with...

   Liked On: 14-08-2023, 05:10 PM

7. 
   zimmer liked post by Tentman On thread : Reloading 6.5x55

   Current 2209. My load workup was done with a fully calibrated GRT calculation, running at a calculated 62,000 psi, well within the limits of brass and rifle, even though over "book max" As I...

   Liked On: 14-08-2023, 12:14 PM

8. 
   zimmer liked post by Ingrid 51 On thread : Reloading 6.5x55

   My Tikka loves both 139 Scenar and 143 eldx. Pic shows eldx @ 100.231132

   Liked On: 14-08-2023, 11:18 AM

9. 
   zimmer liked post by norsk On thread : Reloading 6.5x55

   It depends on what you are after? As a "bang flop" cartridge I think a 308 has the edge,for flat shooting and mild recoil/little blast the old Swede is hard to beat. I have a couple and have had a...

   Liked On: 14-08-2023, 11:00 AM

10. 
    zimmer liked post by mikee On thread : Reloading 6.5x55

    Better performance than a Creedmore, more capacity. Under rated, in a modern rifle with modern barrel they are bloody good (but not trendy)

    Liked On: 14-08-2023, 10:59 AM

11. 
    zimmer liked post by BenTheBuilder On thread : FL resized rounds wont chamber

    yes you are correct. the round reading 45.86mm fits and the round reading 46.05mm does not.

    Liked On: 13-08-2023, 08:55 PM

12. 
    zimmer liked post by kiwijames On thread : 284 seating depth query

    FYI you have the bullet siiting too deep into your vernier jaws. It's is not reading a correct measure. Your actual length will be longer than 3.2".

    Liked On: 13-08-2023, 08:31 PM

13. 
    zimmer liked post by hunter1996 On thread : Show us your DIY gunsmithing jobs

    Rem 700 bolt handle upgrade, bit different than the usual. Cut the handle nearer to the bolt & machined a bit of round down with help of a work mate. Tig welded together, grind handle + stock to...

    Liked On: 13-08-2023, 07:55 PM

14. 
    zimmer liked post by Micky Duck On thread : Whats the longest shot youll confidently take at an animal

    with the .270 its 300-350 absolute maximum on deer...wallabies have no range limit,either they die or are missed.

    Liked On: 11-08-2023, 03:36 PM

15. 
    zimmer liked post by blip On thread : Firearm storage near National park village

    They dont broacast what they are doing on the internet...

    Liked On: 11-08-2023, 11:42 AM

Page 18 of 100 First ... 456789101112131415161718192021222324252627282930313268 ... Last

• Jump to page: