I got mine from Brownells. Only thing I have found with mine is that with moving thru bush and crap if you don't hold the slack in the sling the swivel can on occassion do a full turn. Next time...
Liked On: 04-07-2020, 04:04 PM
For years I have used Lyman's M dies. They create just the right amount of flare to start cast projectiles. Also work for flat based jacketed projectiles. Some dies have the flaring function eg...
Liked On: 30-06-2020, 08:52 PM
I measure inside the extractor groove with a blade micrometer. Don't have any belted mags so cannot comment on them. Be careful though you can draw incorrect pressure conclusions with this method....
Liked On: 30-06-2020, 05:01 PM
I measure inside the extractor groove with a blade micrometer. Don't have any belted mags so cannot comment on them. Be careful though you can draw incorrect pressure conclusions with this method....
Liked On: 30-06-2020, 02:06 PM
I was reading up on this a few months back with respect to watches. At what point can the watch have the "made in" whatever country? I think it was Japan I looked at that if a certain percentage of...
Liked On: 28-06-2020, 09:50 PM
Long time since I fired any of my Sniders. IIRC I used SPANZ brass which was machined from solid stock. I never used substantial loads - my favourite Snider is a Cavalry Carbine. Heavier loads...
Liked On: 25-06-2020, 05:26 PM
For the last 20 odd years I have had an ancient Leupold 3x on my Weihrauch HW80 springer. In it time the HW80 was one of the most powerful springers around. The 3x Leupold scope was quite commonly...
Liked On: 17-06-2020, 06:27 PM
For the last 20 odd years I have had an ancient Leupold 3x on my Weihrauch HW80 springer. In it time the HW80 was one of the most powerful springers around. The 3x Leupold scope was quite commonly...
Liked On: 17-06-2020, 06:25 PM
Nothing wrong with CCI SVs. Some of my best sub moa groups with my Lithgow at 100yds have been shot with it. Just you get more odd flyers with it. Less than satisfactory 100 yd groups have been...
Liked On: 13-06-2020, 06:57 PM
I've got this Ryobi one https://youtu.be/1smil5PldgY It's bloody brilliant. Auto set pressure for tyres. Reasonably fast. Also does air beds, inflating and deflating. Same issue though as all...
Liked On: 13-06-2020, 03:24 PM
This chart below is old. Got it from accurateshooter.com originally IIRC. Those listed are exactly the same. Care needs to be taken with equivalent charts, (and burning rate charts) they only...
Liked On: 09-06-2020, 07:26 PM
This chart below is old. Got it from accurateshooter.com originally IIRC. Those listed are exactly the same. Care needs to be taken with equivalent charts, (and burning rate charts) they only...
Liked On: 08-06-2020, 08:51 PM
That ring you can see will line up nicely with the seperate stub. Section a case end for end for a better view. With a belted case like the 7mm RM it is often better to headspace off the shoulder...
Liked On: 08-06-2020, 04:42 PM
Power supply and after that load cell most likely kaput. I had a partly buggered ps but the symptoms were different to yours. I could still calibrate but when mine was dispensing it would stop at...
Liked On: 07-06-2020, 10:18 AM
Nah it was just if adding a blade to the existing foresight , if the attaching method is not robust it could get knocked off plowing thru bush etc.
Liked On: 06-06-2020, 03:41 PM