7mmwsm cheers for the pics.
Type: Posts; User: Baz
7mmwsm cheers for the pics.
Where was the controlled burn?
7mmwsm I looked on the doc pesticide summaries and it only shows pindone in bait stations on west of Ranginui road, 1080 has been applied in Pouakani reserve and the small block East of Ranginui...
Anyone know what the condition of the access track off Ranganui road is like lately?
Surely the indent made by new factory rifles shouldn’t be acceptable?
Didn’t make any difference with a change in primer make. Same indent
I got it bushed by Robbie at Gunworks. $85 plus...
Interesting, I have a Remington 270 that is 1990 ish year. No primer indent on that one. Never been worked. I had been told the indent in the 7mm is one of the worst seen.
Finally got my factory Remington bolt firing pin hole bushed
Pic showing before and after. Same hand load/primer etc
Remington Sendero SFii rifle to be exact. Must have slipped past the QA
...
Sorry. SOLD
A portable design I am working on.
The 2 pipes are off the shelf steel. NB 80 medium wall for the main upright, OD 88.9mm, sleeve is NB 90 40S with OD 101.6mm and 5.74mm wall giving 0.61mm...
No import permit required for reloading components. US export permit will still be required tho.
The best design machine I have seen so far in link below, I am 90% finished on a table top saw blade type one but the case spin set up has had me mucking around for hours trying to set up and still...
Same, none on serious site, I'd say serious locked them up so no one can get hold of them. was going to give them a call too, see how you get on, I will take 10mm (.40cal) and a mate might want some...
STOCKISTS | WESTCASTINGS PROJECTILES
International Sales – New Zealand
Serious Shooters
726 Great South Road, Penrose,
Auckland, New Zealand
+64 (9) 579 3006
Was that Wyatt from the local trail blazers club that was bringing them in? mate buys from him to. wanting to get an order in as well.
Can the LabRadar be shipped out of the USA?
The standard LabRadar can be shipped to Canada and Australia. A slightly less powerful version can be exported to other countries. The less powerful...
I saw a post by someone on their Facebook page mentioning bad service, (over promising and under delivering).
Dead keen on a review if you get hold of one!
475 deg F on case body below shoulder and 750 deg F inside case neck.
Will only need to do a few cases in initial set up of my machine each time.
Finally looks like a chronograph is available that will surpass all existing types and models.
LabRadar
LabRadar - My Personal Radar
Just brought some from here:
Tempilaq Liquid - Buy Tempilaq Online
After trying to find some for over a year, so now I have the motivation to complete my annealing machine.
Loading up a few upwards from 61.5gr and see if it comes back into a node.
Looking more to an accurate load because if it bug eyes and 100 it should be at worst MOA at 300, this allowing for more...
Banana from talking to George after prize giving, you did well. I was spectating the Saturday, saw you run this stage. was a good run. The Rotorua range is impressive, that's for sure.
Cheers for the advice, it always seems to come back to the 130gr should be doing 2900-3000 fps.
Shot a very similar group to #3 (59gr 2213SC) using the same prod, seating depth etc but 54.5gr 2209...
Hi All
Load developing for my Rem 700 rifle in .270Win. 22" pencil pipe barrel. wanting a good load for up to 300yd. Prod is Hornady 130gr SST. CBTO 2.800"/ 0.01" jump
See the pics of 2 loads...
An import permit WILL be required at this end, you will need an E cat endorsement and a E cat registered firearm on your licence.
Some info to confuse you some more.
The $100 limit only applies to certian 'parts' $500/$100 Export Exemption Details | Borderview | Firearm Export Services to Canada and more!
Search ITAR and...