I own a few Mp, the brass HP ones are heavy but excellent, the aluminium 8 cavity ones are awesome for casting lots and fast.
Sent from my CPH2305 using Tapatalk
Type: Posts; User: Davecbnz
I own a few Mp, the brass HP ones are heavy but excellent, the aluminium 8 cavity ones are awesome for casting lots and fast.
Sent from my CPH2305 using Tapatalk
I have an Noe HP mold about 235 gn and 2 mp hollow point molds one 230gn and one 125. Trouble is they're all packed up as we're moving
Sent from my CPH2305 using Tapatalk
Not a bad idea, but I don't pan lube so I the lube sizer does the job (or a push through die if I'm powder coating)
Sent from my INE-LX2 using Tapatalk
I've heard the same about 6.5 147 eldms and seen video of them going off. I've only run about 50 of them so can't say. But 1 guy said he had run 300 in his prc with no issues and now they're blowing...
'Gordon's reloading tool' is what I was after
Sent from my INE-LX2 using Tapatalk
Fired case capacity in grains of water? and the actual length of a 125sst? And I can sort the data when I'm home. Also look up Gordon's reloading? It's a free app for your computer, it does what...
Outdoor supplies show the bullet feeder but not the primer feed. I used to get mine from fsreloading, but not for some years
Sent from my INE-LX2 using Tapatalk
Or not, that looked OK before I posted it
Sent from my INE-LX2 using Tapatalk
You could manually fill in and save as trailbosshttps://uploads.tapatalk-cdn.com/20200630/3596e7bf3927f0988653039ddbabd734.jpg
Sent from my INE-LX2 using Tapatalk
Cartridge? barrel length from the muzzle to the bolt face? projectile and is actual length,? fired case capacity in h20? And your powder load?
Sent from my INE-LX2 using Tapatalk
How low of a temp are we talking? I'm assuming somewhat lower than ezyflo. What are you joining?
Sent from my INE-LX2 using Tapatalk
+1 for the crc lanolin spray, it works well. I also use the crc lanolin grease on a lube pad or with fingers
Sent from my INE-LX2 using Tapatalk
Looking good so far. I built one some years ago, made a few dies, swaged some 357 projectiles out of 9mm brass, made a de-rimming die for 22lr brass and that's about where it stopped due to to many...
I just do the budget dishwashing liquid and citric acid, if I want shiny I'll change the water after half and hour or so and give it an hour more, rise all the soap off, and dry in the dehydrator, a...
Hornady 230 fmj rn, 5gn bullseye= 1069 fps @ 16070 psi and muzzle pressure 511psi.
With as30 at 4.5gn= 996fps at 19429 psi muzzle pressure 340 psi.
5gns of as30 run 1057 fps at 23557 psi (over...
workshopinnovation.co.nz/products.asp?cat=122&pg=4.
Lee pacesetter dies shows in stock
Sent from my INE-LX2 using Tapatalk
Think I saw 303 savage dies on trademe last week don't know if they sold or not
Sent from my INE-LX2 using Tapatalk
Bit of a cheats way to cut and threading a bolt handle.
The black plastic knob works mint, but I thought I'd make a...... Wait what's that your machining in photo...
5/16" by 36 tpi
Sent from my INE-LX2 using Tapatalk
Reloading is a lot like making home brew, it's cheaper but you won't save much money cause you'll get through more of it[emoji106]
Sent from my INE-LX2 using Tapatalk
Cold blue? As in birch wood type in a bottle? It doesn't add rust protection, slow rust blueing does and hot caustic blueing does offer rust protection. Slow rust blueing would cost an arm to get...
Check with doc as they close some of it off for hunting this time of the year, if I remember correctly between Mt aurther and the cobb.
Sent from my INE-LX2 using Tapatalk