22 Squib load

Put a new scope on my little Brno 2e this morning and picked up a box of CCI mini mag when I was in town earlier. This wee rifle has always been deadly accurate and will stack everything on top of each other at 50yds. Anyhow.. went out to sight it in, boresighted by eye then got into it, got it near enough and shot a group, yeap still shoots mint as.
Then I decided to shoot another group at 75yds, fired first shot, then second shot was just a dull thud, I should have checked the barrel but proceeded instead to fire another shot, the thing actually recoiled unlike a normal 22 and didnt even hit the target fullstop..
I think it had a squib in it because now its shooting all over the show ( anywhere from 5-10" at 50yds) and when I removed the bolt and look down the barrel I can see this ring that looks like it cuts through all the rifling about 4" from the end of the barrel.
Tried cleaning etc, ring is still there and really pronounced like something has cut a ring with a dremel from the inside.
Sound like a squib? Might have to get it cut right back short I think to restore accuracy? Shame as it aint cool chopping up these cool little guns.

Quote:

---

Originally Posted by Ryan_Songhurst

Put a new scope on my little Brno 2e this morning and picked up a box of CCI mini mag when I was in town earlier. This wee rifle has always been deadly accurate and will stack everything on top of each other at 50yds. Anyhow.. went out to sight it in, boresighted by eye then got into it, got it near enough and shot a group, yeap still shoots mint as.
Then I decided to shoot another group at 75yds, fired first shot, then second shot was just a dull thud, I should have checked the barrel but proceeded instead to fire another shot, the thing actually recoiled unlike a normal 22 and didnt even hit the target fullstop..
I think it had a squib in it because now its shooting all over the show ( anywhere from 5-10" at 50yds) and when I removed the bolt and look down the barrel I can see this ring that looks like it cuts through all the rifling about 4" from the end of the barrel.
Tried cleaning etc, ring is still there and really pronounced like something has cut a ring with a dremel from the inside.
Sound like a squib? Might have to get it cut right back short I think to restore accuracy? Shame as it aint cool chopping up these cool little guns.

---

Sounds like you bulged your barrel.
Lucky no other damage as for its size the 22 generates quite a bit of pressure.


Sent from my SM-G965F using Tapatalk

Sounds like a barrel bulge. Bugger. You may be able to feel it on outside be running your hand down the barrel. Can happen when oil is not cleaned out of bore too. Only fix is to chop the barrel behind the ring/bulge. What a shame...still it will leave u with more than enough barrel to get a .22 up to full speed.

Cant feel any bulge on the outside, the ring looks like a clean cut about 1mm wide right round the barrel at a point about 4" from the muzzle. Im guessing there was a shit load of pressure and heat at that spot when one projectile met the other. Bugger

Also... should I be taking that box of ammunition back to retailer in case its a batch issue? Was one of the 100 round bricks and I was only 9 rounds into it..

Not a gunsmith or engineer, but if you wanted to save the original barrel profile, but still needed to get rid of the damaged section, it might be possible to drill the rifling/inside of the barrel out for those last 4 inches, so it looks the same on the outside, but just has a slightly oversize bore for that section?

yes take it back or email the manufacturer with batch number etc...pity to shorten rifle but its no use if cant hit side of cow let alone a bunny.... thread it at same time..should be about $60 to get it done.

Quote:

---

Originally Posted by StrikerNZ

Not a gunsmith or engineer, but if you wanted to save the original barrel profile, but still needed to get rid of the damaged section, it might be possible to drill the rifling/inside of the barrel out for those last 4 inches, so it looks the same on the outside, but just has a slightly oversize bore for that section?

---

That's a bloody good idea[emoji106]
Crown should be easy enough but it will be interesting after that.

Sent from my SM-G965F using Tapatalk

It will still be long enough for a 22 but sure is a shame putting a bulge in the barrel. Pays to check those duds just in case it's stuck in the barrel.

Get it rebarrelled to something else - 7mm Rem or something.

Quote:

---

Originally Posted by Frodo

Get it rebarrelled to something else - 7mm Rem or something.

---

A rimfire one?

Sent from my SM-G965F using Tapatalk

Dropped it off to gunworks yesterday, picked it up just now. Super stubby now! Was going to be under minimum length so gunsmith did what @StrikerNZ suggested, cut it down as to minimum length then counterbored the crown which is now about an inch down inside the barrel. Shoots good again :)
Attachment 105936

As much as it sux to have to cut down such a classic rifle, as long as it's yours it has another story to tell. I'm sure it has loads of stories and memories tied up in it, this is just one more.
Glad it still shoots good mate :thumbsup:

Quote:

---

Originally Posted by dannyb

As much as it sux to have to cut down such a classic rifle, as long as it's yours it has another story to tell. I'm sure it has loads of stories and memories tied up in it, this is just one more.
Glad it still shoots good mate :thumbsup:

---

Theres a 4 month long blank space in its memories where it spent a bit of time hiding in a paddock....

4 months of leaving her out in a paddock; exposed to the weather, without any food or shelter.

Then you feed her shit, to the point she gets severely constipated and requires skeletal reconstructive surgery.

And now you're plastering images of her in her deformed state all over social media.

You'd make a great parent.

Quote:

---

Originally Posted by Ryan_Songhurst

Theres a 4 month long blank space in its memories where it spent a bit of time hiding in a paddock....

---

Attachment 105951

How did that happen?:wtfsmilie:

Quote:

---

Originally Posted by Chur Bay

How did that happen?:wtfsmilie:

---

Sat it on roof of the ute then drove off and lost it for 4 months haha

Surprsisingly it still shot awesome after that wee episode

Well that sure wasn't anywhere near the coast.... Salt spray would have eaten it alive.

She's had a hard life, that's for sure! But the new look is pretty cool. I like short 22s.

Mate lent me his rossi 44 the other day with a box of had loads to shoot a comp
1st shot squibed lucky I noticed and looked down the bore
Taped it out with a rod and kept shooting
He said lucky it was me coz he probably wouldn’t have noticed
His cowboy loads are light as hell with no recoil and with muffs on its easy to get cought of gard

I had a brno with a bulge probably from the same sort of thing (before I got it)
Shot like a demon
I Geuss alot depends where the bulge is