Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Alpine DPT


User Tag List

+ Reply to Thread
Page 6 of 8 FirstFirst 12345678 LastLast
Results 76 to 90 of 119
Like Tree103Likes

Thread: 7mm SAUM, WSM, Blaser Magnum, Rem Mag and 284 Superpig Discussion

  1. #76
    Member chainsaw's Avatar
    Join Date
    Jul 2014
    Location
    Norf
    Posts
    5,430
    Does the empty brass chamber ok ? Then won’t chamber with pill ? What’s the neck diameter before and after loading a pill? Do you have a way of measuring the coal to lanz like Hornady case and gauge ? What part of country are you?

  2. #77
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    Empty brass goes in mint but soon as you load a pill it is a major struggle or will not go at all. Will measure before and after tomorrow. No way to measure coal to lanz but seems to be more of a neck issue than a throat issue as no marks on pill from rifling. I am in Auckland.

  3. #78
    GWH
    GWH is offline
    Member
    Join Date
    Jul 2012
    Location
    Napier, Hawkes Bay
    Posts
    4,456
    iirc they used the reamer with a .317 neck dia. Is that correct?

    If so you'll need to neck turn your brass, same as mine

  4. #79
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    Unsure what the neck was chambered too as gunworks just swapped the barrels over. Will look into neck turning as never done that before. Cheers bro

  5. #80
    Member chainsaw's Avatar
    Join Date
    Jul 2014
    Location
    Norf
    Posts
    5,430
    My 284 loads measure .314 - 315 with Nosler brass and 0.315-316 with Norma. Haven’t measured any Winchester brass but have some so can check
    superdiver likes this.

  6. #81
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    @GWH looking at the cost of a neck Turner it would be cheaper for me to have it rechambered!
    GWH likes this.

  7. #82
    GWH
    GWH is offline
    Member
    Join Date
    Jul 2012
    Location
    Napier, Hawkes Bay
    Posts
    4,456
    Quote Originally Posted by superdiver View Post
    @GWH looking at the cost of a neck Turner it would be cheaper for me to have it rechambered!
    Yes and a lot less ongoing hassle

    Sent from my SM-G930P using Tapatalk
    superdiver likes this.

  8. #83
    Member stagstalker's Avatar
    Join Date
    Jul 2018
    Location
    North Island, New Zealand
    Posts
    2,120
    Pretty sure my loads with winchester brass measure about .314 - .315
    superdiver likes this.

  9. #84
    Member sneeze's Avatar
    Join Date
    Dec 2011
    Location
    nelson/marlborough
    Posts
    3,349
    Quote Originally Posted by superdiver View Post
    Well this is not ideal. Run the brass through a fl resizing die(brass happily Chambers) but as soon as I load up a round it will not chamber at all. Anyone have any ideas???? Losing my mind at the moment
    Make sure you havent screwed the seating die in to far. It can crush the case causing a bulge at the shoulder. Colour a round with the marker pen , chamber it, the scratches should show where the case is binding.
    Last edited by sneeze; 02-03-2019 at 09:36 PM.
    Puffin, mikee, superdiver and 2 others like this.
    "You'll never find a rainbow if you're looking down" Charlie Chaplin

  10. #85
    Member
    Join Date
    Jul 2015
    Location
    Nelson
    Posts
    342
    Have you check the primers are seated properly? I had the same thing happen to me recently. Sized they fitted but loaded they didn't. Turns out a new cartridge to me and even though same brand of brass as I use in other calibers my seater was leaving them a couple of thou proud. Adjusted the seater and problem gone. Hard to see by eye but putting a straight edge across the base showed it up. Since I was only bumping the shoulder back a couple of thou it created a problem as the primer took up more room than there was so a tight on close bolt
    superdiver and xtightg like this.

  11. #86
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    @sneeze we crushed the first round and then backed it right off so that is not the issue we think. @r87mm will check when I do some more loading mid week(have to do it at a mates and he is not local to me) but don't 5hink that is the issue. Seems more to be with the neck of the brass

  12. #87
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    So went and saw @chainsaw who was good enough to help me out. Looks like I need to ream the neck again ffs. Loaded ammo measuring 0.3155" would not chamber so think I will get it opened up to 0.317 or 0.319. Any thoughts or suggestions welcome.

  13. #88
    Member stagstalker's Avatar
    Join Date
    Jul 2018
    Location
    North Island, New Zealand
    Posts
    2,120
    Quote Originally Posted by superdiver View Post
    So went and saw @chainsaw who was good enough to help me out. Looks like I need to ream the neck again ffs. Loaded ammo measuring 0.3155" would not chamber so think I will get it opened up to 0.317 or 0.319. Any thoughts or suggestions welcome.
    If your not gonna neck turn brass then i’d say go .319 pretty sure mine is .318 running standard winchester brass.
    superdiver likes this.

  14. #89
    Member
    Join Date
    May 2015
    Location
    Nz
    Posts
    2,929
    @Monk @Sako85 how do you guys find those 178 eldx go up close? Mate is about to build a 20" 300wsm like your ones and he is sold on that bullet so trying to get info for him. Cheers

  15. #90
    Sako85
    Join Date
    Aug 2014
    Location
    Palmerston North
    Posts
    277
    Quote Originally Posted by superdiver View Post
    @Monk @Sako85 how do you guys find those 178 eldx go up close? Mate is about to build a 20" 300wsm like your ones and he is sold on that bullet so trying to get info for him. Cheers
    The closet deer I have shot with 178 eld x was a Stag at 360 yards, and it sacked him, I haven’t used them enough to say how they go up close, sorry not much help I know.
    I mainly run 168 Amax at various ranges which i have been happy with in the 300 wsm and 308 , but have since upgraded the scope on the wsm and am about to run 208 Amax and or 190 VLD Bergers

    Cheers

 

 

Similar Threads

  1. Magnum to SAUM conversion
    By HuntGatherRepeat in forum Firearms, Optics and Accessories
    Replies: 4
    Last Post: 02-09-2017, 09:29 PM
  2. 300 Blaser Magnum
    By 300AAC in forum Reloading and Ballistics
    Replies: 8
    Last Post: 11-06-2017, 08:11 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!