Printable View
Hi,
Just joined today as a new member.
Can anybody recommend an upper North Island or generally North Island based gunsmith competent with corrective work on the Winchester M70 CRF action ?
I'm experiencing a minor extractor issue causing a bit of brass damage and want to find out if it can be cured. Not major, but annoying.
Thanks for any help. Cheers
Arthur Cleland in Hamilton has been great. He did most of my work. Good quality and below average pricing.
Not sure if he is retired though.
Cleland Gunsmithing and Engineering
Do you have a picture of the damages on the brass please?
dean maisey in tauranga or david dwenn at SAI penrose.
Not the best pic sorry but shows what I'm talking about. Brass in the extractor groove is being cut by the sharp edge of the extractor. Also I'm finding the belt is getting roughed up as well. The scarring on the case body occurs on chambering but is now at least partly corrected. At first brass shavings were deposited into the chamber cut for the case belt but now that's fixed only some light body marking still occurs. I don't like it but can live with it as it probably has minimal affect on brass life. I have a push feed action same calibre and none of this happens and would like the CRF M70 operating to the same level.Quote:
Originally Posted by Friwi
.375 H&H.
https://i.postimg.cc/05zHWB2F/20221024-085634-Copy.jpg
Many thanks Muzza. He's in an ideal location. Looking at his website info suggests he should be qualified and at least well worth talking to. I'll send an enquiry his way. Cheers.Quote:
Originally Posted by muzza
Thankyou. Have dealt with David Dwen. I think this particular issue might be better with more of a specialist. No slight on David though. Helpful and good guy to deal with.Quote:
Originally Posted by Russian 22.
Cheers.
https://www.guntechnz.co.nz/about-us
Cobus has done some good work for me .
I've also had good work done by him. I believe he has relocated to Te AwamutuQuote:
Originally Posted by jakewire
I think he still on holiday in South Africa at the moment but maybe call first.Quote:
Originally Posted by Manchester
Thanks all round guys. Very helpful info and suggestions. I've emailed Cobus but no reply yet. Maybe still on leave as noted. I'll give it a while before following up. No great urgency yet.
Cheers.
Gone back to SA, meant to be returning and setting up in Te Awamutu.Quote:
Originally Posted by muzza
Those are some weird graunches on the case body! How sharp are the feed lips on the mag? The extractor must have a pretty sharp edge to damage the extractor groove on the case?
Allen Carr would be the ultimate CRF expert..
To my feel the feed lips don't seem sharp or strongly edged. I think the edges have probably been softened. I don't think they are causing the brass scarring.Quote:
Originally Posted by 6x47
One thing I'm not sure of is where the mag box meets the feed ramp and whether the chambering case scrapes over this junction...??? Need to look at this more closely. Possibly the top edge of the mag box is a tad high...??
OK, thanks for the tip. Since a return date for Cobus seems unknown I rang Allen today. Might be meeting him mid November.Quote:
Originally Posted by HandH
Take a look inside your chamber the best you can with a good torch light, and see if there are any traces of rust.
I had that happening before . Some very light polishing with fine steel wool wound up on a rod and gun oil took care of the problem.
Jut a post update.
Received a reply from Cobus yesterday saying he is unable to assist with gunsmithing currently due to being overseas for an extended period tending to serious matters. There was no mention of an expected date of return to NZ.
I assume from that he expects to be out of the picture for a while.
Arthur still is about - just has limited hours during the day - though when I was last there a few months back, no shortage of courier boxes in and out!!Quote:
Originally Posted by Synthetic
Hes always good for a call... very helpful.