Not the Suzuki. I'm in a river channel which floods. I've spent days operating it like a boat. Roads turning into swift flowing rivers where forcing up stream results in jets of water squirting out of the plastics. No dramas.
Printable View
One thing I would recommend if you get a King quad is to have the dealer swap the stator out for one from one of their roadbikes (can't remember what model but lot more capacity and direct swap) my old man runs one of these shooting for a dollar, he trades for a new one every year and had two of them let him down out in the back of nowhere because the stator can only just keep up with running the engine and lights on the bike, run a spotlight or a thermal on charge for a couple hours and they won't keep up and end up killing the stator packs, the battery dies and ultimately you're left stranded, even having an extra light bar on the bike itself and a uhf hardwired to the bike puts them at their very limit. Last two he's had they have fitted the upgraded stator and no problems. He also has a pull start off one of his old 500s and has it fitted to his new bike each time he gets one as the 750s don't come fitted with any kind of auxillary start, they're a bloody mission to pull start but can get you out of the shit
Good advice, we don't have any auxiliary electrics and still replace stators regularly.
I can say ours get absolutely flogged. I have two at the moment because I like my old one so kept it. It's got 46,000km on it and right now I'm pulling to its absolute limit in 4x4 on the original belt.
Sent from my CPH1701 using Tapatalk
I'm genuine when I say I have never dealt with a piece of machinery of any kind that is this tough. Really good things. Take day to day abuse and still pretty low maintenance. My family can be very very hard on machinery. This bike was a bull chaser ridden like a dirtbike for years and has been pulling big K-lines since new. Asked the shop to go over it as it was old and due to trade and was told "basically nothing wrong with it". We don't have Utes (which is super annoying). You want to carry a load of fence posts or literally anything else, it does on the quad.
If you are a hunter using it recreationaly, as long as basic servicing is kept up with and it's stored well, given a run occasionally, I can't imagine them giving any trouble.
Sent from my CPH1701 using Tapatalk
Mine is a 09 king quad 750, best machine I've owned, never had an issue with the stator problems you guys are talking about, there is a mod that can be done to the regulator rectifier by using a bigger gauge cable to the batt from memory due to the standard one being a shoestring, have done this with mine and haven't had any issues especially with doing extended Winch pulls. There's a few tricks you can do with the CVT clutch system to get them going better too, I've machined 2mm off the primary clutch and fitted a 0.5mm shim Bettween the primary sheeves which allows the belt to ride deeper which calculates to 30% more torque low down but decreases top speed by like 5kmh. Added a vdi copperhead ecu which changes ignition and fuel tables and is live mappable it Lso removes the rev cut with diff lock and when in reverse. One thing to keep an eye on is cracking in the frame if you really giving them a hard time I ended up welding in som supports and braces to help stop this. All in all great machines. Mine ears the big canams for breakfast.
I would like to get one and fiddle with it. They also go quite fast, though due to the fun police, I am no longer allowed to do this. 4WD power slides are a lot of fun.
Got any suggestions for gearing the gearbox up? My uncle bought the 500 as a hair shirt. He hates it with a passion. Its geared way down, so it sounds like its in low ratio when you cruise around.
The suspension on this new 500 is nuts. Much better than the older ones, on hills it feels like it just won't tip over.
Cvt quads don't really use a gear box as such, they use a primary and a secondary clutch consisting of 2 sheeves per clutch. Both clutches work together depending on engine rpm and wheel speed. From a dig the primary is wide open allowing the belt to ride low in the sheeves while the secondary is pulled closed so the belt rides high. As engine rpm and wheel speed increase counter weights in the primary under centrifugal force force it closed pushing the belt up to ride high and its the opposite for the secondary. It like the gears on ya mountain bike but it's constant velocity. You can't really gear them up as the clutches would have to be a bigger diameter. Taller tyres may make a difference but at the sacrifice of low down torque. The cvt is pretty cool to tinker with heaps can be done, from machining the sheeves, lightening the counter weights in the primary, uprated secondary clutch spring. Doing all that to 750cc big boy quad makes it another machine. Mine will wheel stand from a get go for along as you can keep in balanced or run out of road lol.
If the vid below works it illustrates how the clutchs work
https://youtu.be/JRHIfoZMD74
Has anyone seen in NZ or use snorkel kits on their quad, as said in the post, river crossings can be killers if water enters them.
Theres heaps of snorkel kit available for different quads, plenty of YouTube vids of guys doing the DIY thing too. I never have othered with mine and its been in some deep water main thin is not to go deeper then the air intake for the engine, the intake for the cvt sys is under the under the handle bars for the king but the exhaust for it sits low under the rear carrier. They have a drain bung but I've never had anything come out of it.
I'm a CVT enthusiast. I like watching bench tests for something to do.
They have told him at the shop they can change something in here.
I think my old bike has a hole in the CVT housing or the breather is broken. It ends up geared high, where taking off its like its in third gear. Very hard to inch along slowly. If you peg the throttle it just launches.
Had it looked at once, they said it was crap in the housing stopping the weights from moving properly. Came back normal but it's back doing it again.
One thing I don't understand is why the brakes are so much better in 4x4?
I also notice when I stop very hard the belt slips a bit and it's like the brakes are stuck on.
Is this something to do with the engine braking?
Sent from my CPH1701 using Tapatalk
If ya housing get full of dust etc youl wear out components, you can pull the primary apart and check the weights they do wear out eventually and end up with flat spots preventing them to roll as such. Belts in these quads apart from canam shouldn't slip the drive belt, they have a wet spragclutch that does all the slipping instead of the belt, canam choose to slip the drive belts instead of running a wet clutch which is why they smoke the drive belts under heavy load if not careful.
Got a '14 KingQuad a few months ago with 20k on it and loving it so far. A lot more comfortable than the TRX500 it's replaced. Fuel injection was a must for the range of altitudes it get's used in and having the low-range trans is useful as well. Like Ryan I've fitted a second hand pull start unit to it just incase. Will still need a bit of juice for the fuel pump but it's a good backup to have. Great engine braking too. Almost wants to stop when going down a steep hill in low. Rode a mates Polaris and that thing would run away bloody quickly unless you kept blipping the throttle quietly.
The Suzuki range is definitely worth a look at anyway.
hey guys just thought id add my $0.02, after discovering this thread and always wanting to get a pull start for my quad I figured id put some effort into doing it.
After some asking my very helpful mates at Ashburton Suzuki we found my 2012 Suzuki king quad 500 has the same crank as a 06-08 450 king quad, they then rang a quad scrapper in the north island and the part arrived Friday when only being ordered Thursday lunch.
$100 and 5 min install and my quad now has a functioning pullstart despite being EFI.
Yeah shes a minta!
Attachment 164747
looks pretty tidy :)
Where does everyone get the tool boxes and dog mats from?
96, 4200 hours, yeah air cooled model. Thinking box & gun mount on front, mat on back and swap out the old 12v plug for a ciggy lighter model for spot/lightbar. That way can poke a air comp or even any usb powered gadget in there. Also need a way to transport a few fishing rods....
Mine came with my bike, not a whites brand one, this was from a place in Wanganui I think, made out of recycled rubber I was told.
Nice and thick, but went to remove it and the thing weighs a tonne. Well 11kgs, that’s 11kg off the arse of the bike.
https://burgessmatting.co.nz/shop/atv-bike-mats/
Knock up a rocket launcher you can clip on and off the front rack. Ali and pop rivets/screws or PVC pipe. Lets you swing your leg over the back rack and you have a seat watching the rods. Just strap a fish bin on the front. If you want to be fancy get a lid on it and attach with a couple of holes and cable ties to make sure it doesn't blow or bounce off.
I don’t have a tool box, use a plastic school desk tote tray, throw my stuff in there and put a hi vis bike bag cover over the top.
I’ve managed to attach the rifle holders to the tote tray, it will do the job with the help of bungy cords
Don't forget the Suzuki stickers! Can let you have a set, LTF300 they say.