10-Ring
Gone But Not Forgotten

1084 Likes

Page 27 of 73 First ... 1314151617181920212223242526272829303132333435363738394041 ... Last

• Jump to page:

1. 
   chainsaw liked post by 10-Ring On thread : AR2206H

   For the last couple of months I've been using a particular 500gm bottle of AR2206H. Wasn't getting particularly good groups with my .308 and the recoil felt quite soft. Anyway put several of my loads...

   Liked On: 06-10-2019, 12:59 PM

2. 
   shooternz liked post by 10-Ring On thread : 200gn Eldx out of 308?

   The 180grn Norma Oryx also a good bullet and very accurate in my 20" .308.

   Liked On: 03-10-2019, 10:43 AM

3. 
   Micky Duck liked post by 10-Ring On thread : 200gn Eldx out of 308?

   The 180grn Norma Oryx also a good bullet and very accurate in my 20" .308.

   Liked On: 02-10-2019, 01:30 PM

4. 
   Micky Duck liked post by 10-Ring On thread : 6.5 Creedmoor load development

   All shooting is good fun, but it can become obsessive. 94259

   Liked On: 30-09-2019, 10:20 AM

5. 
   Micky Duck liked post by 10-Ring On thread : 6.5 Creedmoor load development

   The 6.5 Creedmoor has a reputation for being an easy cartridge to develop an accuracy load for. I've found this to be true in my case, however that's with the caveat of only trying five powders and...

   Liked On: 30-09-2019, 09:56 AM

6. 
   SlimySquirrel liked post by 10-Ring On thread : 6.5 Creedmoor load development

   Same as Flyblown, love those 143 ELD-X for their flat trajectory. This fat fallow was shot on a very steep downhill slope at 296 yards. Bullet entered just below the right eye and exited as in the...

   Liked On: 29-09-2019, 09:22 PM

7. 
   SlimySquirrel liked post by 10-Ring On thread : 6.5 Creedmoor load development

   Wingman. I would say almost certainly you have a bad batch of AR2209. The two 500g lots I've used up were ME M5675 and ME M5583 plus 1lb H4350. None gave any excessive pressure even up to 45gr with...

   Liked On: 29-09-2019, 09:22 PM

8. 
   chainsaw liked post by 10-Ring On thread : Annealing, neck turning all that attention to neck tension and true Centering

   It's not a magical answer to accuracy as you say. However, in an accurate firearm with a good shooter, uniform neck tension is something that contributes to increased accuracy. As repeatable accuracy...

   Liked On: 27-09-2019, 02:26 PM

9. 
   rewa liked post by 10-Ring On thread : Annealing, neck turning all that attention to neck tension and true Centering

   It's not a magical answer to accuracy as you say. However, in an accurate firearm with a good shooter, uniform neck tension is something that contributes to increased accuracy. As repeatable accuracy...

   Liked On: 27-09-2019, 12:56 PM

10. 
    Moa Hunter liked post by 10-Ring On thread : Swaro or Leica

    Be aware that the Leica guys at the Sika Show have in past years quoted the RRP and tell you they're giving a special discount on the day. The reality is their discounted price is no bargain because...

    Liked On: 27-09-2019, 12:06 AM

11. 
    6x47 liked post by 10-Ring On thread : FL sizing without expander ball

    Quite agree, I've never had a problem with expander mandrels causing run-out.

    Liked On: 19-09-2019, 08:58 PM

12. 
    6x47 liked post by 10-Ring On thread : FL sizing without expander ball

    Well I'm definitely pedantic - case in point, a collet neck die doesn't work the neck any less than a bushing die if the neck wall thickness is equal all round. However, most unturned cases have...

    Liked On: 19-09-2019, 08:57 PM

13. 
    Steelisreal liked post by 10-Ring On thread : FL sizing without expander ball

    Well I'm definitely pedantic - case in point, a collet neck die doesn't work the neck any less than a bushing die if the neck wall thickness is equal all round. However, most unturned cases have...

    Liked On: 19-09-2019, 11:56 AM

14. 
    bully liked post by 10-Ring On thread : Projectile Bearing Surface vs neck contact vs jump to lans

    Your mate is right, especially for hunting. With rounds in a magazine the bullet can move back under recoil. You can of course get away with less but only advisable in a controlled single load target...

    Liked On: 15-09-2019, 09:10 PM

15. 
    kiwijames liked post by 10-Ring On thread : 38Win brass and neck bushing

    I use a .336 bushing on Lapua .308 brass. Have used a .335 bushing which of course, increases neck tension but accuracy isn't as good in two different Sako rifles.

    Liked On: 15-09-2019, 03:10 PM

Page 27 of 73 First ... 1314151617181920212223242526272829303132333435363738394041 ... Last

• Jump to page: