11mms
Member

187 Likes

Page 12 of 13 First 12345678910111213 Last

• Jump to page:

1. 
   11mms liked post by IamHackmeat On thread : new trigger

   so a while a go i had a major cock up and broke the trigger on my a bolt. after lots of stuffing round trying to get a new one id given up . i get call from an uncle and he's got a mate who likes to...

   Liked On: 27-08-2023, 09:01 AM

2. 
   11mms liked post by gundoc On thread : Re tension a spring?

   When you are happy with the tension after bending then bring it to a full cherry red on a piece of flat steel by heating under the steel then allow to air cool. It is now fully annealed. Repeat the...

   Liked On: 27-08-2023, 08:57 AM

3. 
   11mms liked post by Micky Duck On thread : What can i do to progress my dogs training?

   work on the big three #come here...now no bullshit,no excuses...NOW # get in behind..now no bullshit,no excuses,NOW #sit...now,no bullshit no excuses NOW......and stay sitting untill I bloody well...

   Liked On: 27-08-2023, 08:52 AM

4. 
   11mms liked post by Flyblown On thread : Prado vs Surf

   jobasa The two vehicles have completely different drivetrains. The Surf is part-time 4WD with selectable high and low range 4WD through a transfer case. The 90 series Prado is full-time 4WD...

   Liked On: 27-08-2023, 08:38 AM

5. 
   11mms liked post by Von Gruff Knives On thread : A Lee Speed stock

   Was able to make a start on the stock this morning and decided that because the Lee Enfield action is so prevalent throughout New Zealand that there may well be others that need to make a replacement...

   Liked On: 27-08-2023, 08:33 AM

6. 
   11mms liked post by Barry the hunter On thread : Knife sharpeners you’d recommend

   scary sharp - made in Hawera are very good but expensive for a fathers day present - but will last for years and you will have a lot of mates wanting to use it - why not a decent oil stone -if one of...

   Liked On: 27-08-2023, 08:32 AM

7. 
   11mms liked post by Markgibsonr25 On thread : Tuatahi Axe

   this is far easier on the back.Nice axe though

   Liked On: 27-08-2023, 08:28 AM

8. 
   11mms liked post by Barry the hunter On thread : 0 lead shot

   reminds me of our rat loads in the huts when bored on wet day - we would take the projectile out of a .222 then shave slivers (tiny) of a .22 mix with wax and put into .222 after tipping out a lot...

   Liked On: 27-08-2023, 08:23 AM

9. 
   11mms liked post by woods223 On thread : My great-niece started her hunting career.

   227067 Put this photo up on another site, unbelievable positive responses. So proud of her getting her second deer, equally proud of her dad for giving her the opportunity and guidance even though...

   Liked On: 27-08-2023, 08:21 AM

10. 
    11mms liked post by Williamfga On thread : .308 ammunition advice

    Fair enough, rifle has been pillar bedded and free floated, shortened / Crowned and checked over by a very trusted gunsmith. The sako gamehead 150g groups around 1moa, Lab radar averaging 2598fps....

    Liked On: 27-08-2023, 08:16 AM

11. 
    11mms liked post by grandpamac On thread : .308 ammunition advice

    Greetings, So far you have tried three types of ammo and none shot better than OK. Perhaps the next step is to get the rifle checked over to see if there is a problem. The .308 will shoot any half...

    Liked On: 27-08-2023, 08:16 AM

12. 
    11mms liked post by Ryan_Songhurst On thread : What would you pay for a pup?

    I think it's retarded breeding dogs just for shits and giggles. Sure if you have buyers lined up wanting pups from a proven dog then knock yourself out but there's enough dogs already in this country...

    Liked On: 27-08-2023, 07:34 AM

13. 
    11mms liked post by bigbear On thread : What would you pay for a pup?

    All depends on location, also timing off litter. The market has been flooded last couple years. A litter of pups is a lot of work if you look after the pups by changing bedding etc, bitch may...

    Liked On: 27-08-2023, 07:32 AM

14. 
    11mms liked post by Maca49 On thread : Old bayonet knife...ID, value, restoration?

    231816

    Liked On: 24-08-2023, 09:12 PM

15. 
    11mms liked post by Blackfern On thread : First attempt at reloading. Thoughts please.

    Evening all. Thanks for all the support and advice. Thought id add some more thoughts after pondering the results and comments for the day. There was a few questions asked through out the thread so...

    Liked On: 24-08-2023, 08:37 PM

Page 12 of 13 First 12345678910111213 Last

• Jump to page: