300Shortmag
Member

93 Likes

Page 2 of 7 First 1234567 Last

• Jump to page:

1. 
   300Shortmag liked post by hotsoup On thread : If you only had one to rule all

   6.5prc or 7saum Happy with either for 1 gun to do it all in NZ

   Liked On: 07-07-2023, 08:04 PM

2. 
   300Shortmag liked post by Sika Seeker On thread : Makokomiko

   Thanks mate that’s helpful to know. Was more after block info though

   Liked On: 04-07-2023, 03:36 PM

3. 
   300Shortmag liked post by SixtyTen On thread : 7mm ss cs 7mm saum vs 7mmsst

   I did a lot of back and forth of which cartridge to use for my project. I was also looking at wildcats based on the SAUM. My criteria was to be able to easily take shots at 600m and have the finished...

   Liked On: 28-06-2023, 07:00 AM

4. 
   300Shortmag liked post by LMcNab On thread : 6.5 Creedmoor? whats everyones thoughts? on hunting performance

   Learning to shoot your rifle is roughly 1000 times more important than what cartridge it is chambered for. Buy a tikka in Creedmoor, stop reading this shouting match and go learn to shoot it. It will...

   Liked On: 11-06-2023, 10:05 PM

5. 
   300Shortmag liked post by XR500 On thread : What outboard to put on a dighy

   ....But you triple your fun!:thumbsup:

   Liked On: 06-06-2023, 08:35 PM

6. 
   300Shortmag liked post by XR500 On thread : What outboard to put on a dighy

   You mean like these?:D Last weeks fun: Go anywhere these things. 4.7m long, 50hp, weighs 150kgs inc motor. Uses about 8L/hr Carry up to 800kgs. 225865

   Liked On: 06-06-2023, 08:33 PM

7. 
   300Shortmag liked post by Larskramer On thread : Sika stag down

   Popped up and into the kawekas over the weekend, On the first arvo my mate shot his first sika at 300, just a tasty little male yearling. The next morning, we headed to another spot and as I...

   Liked On: 06-06-2023, 12:21 PM

8. 
   300Shortmag liked post by Doon On thread : 6.5prc

   ADI has load data for ar2225 which is similar to retumbo on there website.

   Liked On: 02-06-2023, 08:21 PM

9. 
   300Shortmag liked post by andyanimal31 On thread : 6.5prc

   Adi 2225 is the same powder as retumbo repackaged for hogdon. Use the same data Sent from my SM-A226B using Tapatalk

   Liked On: 02-06-2023, 08:17 PM

10. 
    300Shortmag liked post by 6.5 CRD On thread : 6.5prc

    I run 2217 in my wifes Tikka 6.5 PRC, 24" Barrel. 143gr ELDX Lapua brass & FED210m Primer. 59gr of 2217 gives me 2960fps & this is what i run it at, shoots great. Have gone up to 60.5gr which gave...

    Liked On: 02-06-2023, 08:17 PM

11. 
    300Shortmag liked post by johnd On thread : End of an era

    Back in the day we had similar welfare calls via radio from the back country out to the front on Bluff / Muzzle stations. Later in life as a linesman I even went on a tuning trip to Molesworth where...

    Liked On: 31-05-2023, 06:55 AM

12. 
    300Shortmag liked post by Mathias On thread : Magnum primers in a 260?

    Yes you should reduce your charge for magnum primers in the first instance. How much, well I'd go back at least 1.5gr and go from there to be safe. You might well end up with the same load but with a...

    Liked On: 15-05-2023, 08:42 AM

13. 
    300Shortmag liked post by 25/08 IMP On thread : Magnum primers in a 260?

    I've always used 215 primers in my .260 and a number of non magnum cal all worked real well. Sent from my CPH2145 using Tapatalk

    Liked On: 15-05-2023, 07:26 AM

14. 
    300Shortmag liked post by Philipo On thread : 6.5 question

    What rifle you running there Tim ? I take it that the PRC is your tops / open country gun, if so then ditch the suppressor, while they reduce noise they also add weight in length. For me on a LR...

    Liked On: 15-05-2023, 07:02 AM

15. 
    300Shortmag liked post by hotsoup On thread : Backlanz vs MTN Gear bipods

    Aye? This doesn't make sense. You know the mountain has pan & tilt feature eh. This has significantly more movement than the backlanz, unsure how you come to that conclusion on close range...

    Liked On: 14-05-2023, 09:22 PM

Page 2 of 7 First 1234567 Last

• Jump to page: