6.5 CRD
Member

473 Likes

Page 7 of 32 First 123456789101112131415161718192021 ... Last

• Jump to page:

1. 
   Trout liked post by 6.5 CRD On thread : Found rifle - Story time

   Run into this at morgan hut - durville valley, lake rotoroa. Assuming it was found somewhere in the durville valley & left at the hut. Surely someone on here knows the owner & story behind it...

   Liked On: 23-10-2023, 10:26 AM

2. 
   Moa Hunter liked post by 6.5 CRD On thread : 7mm PRC

   25/08 IMP for what its worth, GRT suggests that 2217 is only 15fps slower than RL26 with a max charge of both. 2217 would be reasonably compressed at that, RL26 wont be. 2225 gives a little more...

   Liked On: 15-10-2023, 08:57 PM

3. 
   TimC liked post by 6.5 CRD On thread : 308 barrel length velocity loss

   There is alot of variables when it comes to barrel length vs speed so theres no real once size fits all, you can estimate and theres some general rule of thumb "x fps for y inches of barrel" you can...

   Liked On: 15-09-2023, 09:57 PM

4. 
   Trout liked post by 6.5 CRD On thread : 308 barrel length velocity loss

   There is alot of variables when it comes to barrel length vs speed so theres no real once size fits all, you can estimate and theres some general rule of thumb "x fps for y inches of barrel" you can...

   Liked On: 13-09-2023, 04:41 PM

5. 
   dannyb liked post by 6.5 CRD On thread : 308 barrel length velocity loss

   There is alot of variables when it comes to barrel length vs speed so theres no real once size fits all, you can estimate and theres some general rule of thumb "x fps for y inches of barrel" you can...

   Liked On: 13-09-2023, 03:29 PM

6. 
   Jus liked post by 6.5 CRD On thread : Should I avoid Hornady brass?

   My opinion differs to Jus but i guess because im not chasing maximum speed, it doesnt matter so much to me. Hornady brass in 7PRC isnt bad if your not chasing every last bit of velocity....

   Liked On: 11-09-2023, 08:43 PM

7. 
   Bowhunta liked post by 6.5 CRD On thread : Should I avoid Hornady brass?

   My opinion differs to Jus but i guess because im not chasing maximum speed, it doesnt matter so much to me. Hornady brass in 7PRC isnt bad if your not chasing every last bit of velocity....

   Liked On: 11-09-2023, 01:46 PM

8. 
   rupert liked post by 6.5 CRD On thread : Should I avoid Hornady brass?

   My opinion differs to Jus but i guess because im not chasing maximum speed, it doesnt matter so much to me. Hornady brass in 7PRC isnt bad if your not chasing every last bit of velocity....

   Liked On: 11-09-2023, 11:52 AM

9. 
   tikka6.5 liked post by 6.5 CRD On thread : 6.5 staball vs 2209

   6.5 Staball will give more speed but at the sacrifice of temp sensitivity. If you have a good load sorted already with 2209, i would stick with that. If you look hard enough, you will find some. Bit...

   Liked On: 04-09-2023, 10:37 PM

10. 
    dannyb liked post by 6.5 CRD On thread : 6.5 staball vs 2209

    6.5 Staball will give more speed but at the sacrifice of temp sensitivity. If you have a good load sorted already with 2209, i would stick with that. If you look hard enough, you will find some. Bit...

    Liked On: 03-09-2023, 09:10 PM

11. 
    BRADS liked post by 6.5 CRD On thread : Hardy vs DPT Suppressors

    Hardy magnum / stealth will outperform any of the dpt offerings for noise reduction. If you want to go one step further, atec h2 will beat them both. Sent from my iPhone using Tapatalk

    Liked On: 29-08-2023, 01:20 PM

12. 
    TimC liked post by 6.5 CRD On thread : Hardy vs DPT Suppressors

    Hardy magnum / stealth will outperform any of the dpt offerings for noise reduction. If you want to go one step further, atec h2 will beat them both. Sent from my iPhone using Tapatalk

    Liked On: 28-08-2023, 07:34 PM

13. 
    Kiwi Greg liked post by 6.5 CRD On thread : Hardy vs DPT Suppressors

    Hardy magnum / stealth will outperform any of the dpt offerings for noise reduction. If you want to go one step further, atec h2 will beat them both. Sent from my iPhone using Tapatalk

    Liked On: 28-08-2023, 07:10 PM

14. 
    rewa liked post by 6.5 CRD On thread : friends asking how much for load development

    Personally i dont load for anyone else other than my brother because although i enjoy it, i cant charge enough to make it worthwhile. If your doing it cheap to help a mate out and dont mind taking a...

    Liked On: 21-08-2023, 09:09 PM

15. 
    GlenM liked post by 6.5 CRD On thread : Short barrel powders (308 and 7mm RM)

    Be mindful of twist rate, the rem mag will be 9 1/2 twist which could be not quite enough for some of the long projectiles in the 170gr range (175 ELDX for example) & the mag length is a problem with...

    Liked On: 19-08-2023, 07:42 AM

Page 7 of 32 First 123456789101112131415161718192021 ... Last

• Jump to page: